EAP-E Telegesis Ltd, EAP-E Datasheet
EAP-E
Specifications of EAP-E
Related parts for EAP-E
EAP-E Summary of contents
Page 1
... Telegesis EAP-E, EAP-E-PA EAP-E and EAP-E-PA Ethernet Access Point ©2009 Telegesis (UK) Ltd PRODUCT MANUAL TG-EAPE-PM-006-104 Product Manual 1.04 EAP-E Product Manual (Rev 1.04) ...
Page 2
... Creating Virtual COM Ports ............................................................................................... 9 5 FIRMWARE CHANGES AND UPGRADES ....................................................................... 12 5.1 Device Reset and manually Entering the Bootloader ...................................................... 12 6 SCHEMATICS .................................................................................................................... 13 7 ORDERING INFORMATION .............................................................................................. 15 8 TRADEMARKS................................................................................................................... 16 9 DISCLAIMER...................................................................................................................... 16 10 CONTACT INFORMATION ................................................................................................ 16 11 REFERENCES.................................................................................................................... 16 ©2009 Telegesis (UK) Ltd Table of Contents - 2 - EAP-E Product Manual (Rev 1.04) EAP-E ...
Page 3
... ZigBee® networks. Using the Ember bootloader custom firmware and firmware upgrades can be downloaded via Ethernet or over the air. The SIF interface also allows the EAP used as a platform for firmware development and debugging. The EAP-E access points also support the use of Ember’s EZSP (Ember ZigBee® Serial Protocol) instead of the Telegesis AT Command interface ...
Page 4
... Telegesis (UK) Ltd Min. Max. 1 -0.3 20 -40 85 Table 1. Absolute Maximum Ratings Min. Typ. Max. 4 235 275 235 275 300 400 235 275 Table 2. Operating Conditions - 4 - EAP-E Units Condition V °C Units Condition +3dBm +17dBm mA RX °C EAP-E Product Manual (Rev 1.04) ...
Page 5
... Device Installation and Operation In order to install the device connect the EAP suitable power supply with the positive supply in the centre of the plug. After that connect it to your network hub DHCP server is connected to your network the EAP-E will automatically acquire an IP address. ...
Page 6
... ATI are repeated. The default Port number of 10001 can be changed to any port number in order to allow multiple EAP- addressed via the internet this the local router/firewall needs to be set up to forward incoming ports to the respective port of the corresponding local EAP-Es. All you need now to connect to your ZigBee® ...
Page 7
... Alternatively you can use the Lantronix® DeviceInstaller to do this as shown in Figure 4. ©2009 Telegesis (UK) Ltd Figure 3: A Telnet Session to the EAP-E Figure 4: EAP-E setup using Telnet to port 9999 - 7 - EAP-E EAP-E Product Manual (Rev 1.04) ...
Page 8
... For a detailed description of the menu settings please consult the XPort® Direct available from www.lantronix.com. The DeviceInstaller is used to change the configuration of the EAP-E on the Ethernet side. In most cases there is no need to alter any of the Ethernet settings and so the DeviceInstaller can usually be ignored. © ...
Page 9
... If accessing the serial port of the remote ETRX2 using Telnet is inconvenient for your application, potentially because you want your application to work with either the Telegesis ETRX2USB, ETRX2CF or the EAP-E in the same way, you can map the EAP virtual COM port in the same way as you can do with the USB and CF devices. ...
Page 10
... After this process any application can access the embedded ETRX2 as though it was connected to the local machine’s COM port as shown in Figure 6. ©2009 Telegesis (UK) Ltd Figure 5. The Lantronix® CPR - 10 - EAP-E EAP-E Product Manual (Rev 1.04) ...
Page 11
... Figure 6: Telegesis Terminal accessing a EAP-E using CPR ©2009 Telegesis (UK) Ltd - 11 - EAP-E Product Manual (Rev 1.04) EAP-E ...
Page 12
... EAP-E access point. You can also use this interface for custom firmware development and real time debugging of your custom firmware. Finally with the advent of EmberZNet3 now possible to download the Ember EZSP (Ember ZigBee® Serial Protocol) as described in section 6 of the EM260 manual to the EAP-E. In case you require ...
Page 13
... Schematics The schematic of the EAP-E is shown on the next page for reference. LED1 and the beeper are future options, which are not fitted. The serial port including the handshaking lines as well as the reset and A/D2 lines can be accessed via labelled pads the SIF connector, which allows programming and custom firmware development and real time debugging in conjunction with the Ember InSight Adaptors and the accompanying development toolchain ...
Page 14
... Telegesis (UK) Ltd - 14 - EAP-E Product Manual (Rev 1.04) EAP-E ...
Page 15
... Telegesis Wireless Mesh Networking Module with Ember ZigBee® Technology: • Telegesis AT Style Command Interpreter and • Ember’s EmberZNet2.x stack • Integrated 2.4GHz Antenna Table 3. Ordering Information - 15 - EAP-E Product Manual (Rev 1.04) EAP-E Where customers wish to ...
Page 16
... Contact Information Website: www.telegesis.com E-mail sales@telegesis.com Telegesis (UK) Limited 3, Abbey Barn Business Centre Abbey Barn Lane High Wycombe Bucks HP10 9QQ UK Tel: +44 (0)1494 510199 Fax: +44 (0)5603 436999 11 References Telegesis - www.telegesis.com Ember - www.ember.com Lantronix - www.lantronix.com ©2009 Telegesis (UK) Ltd - 16 - EAP-E Product Manual (Rev 1.04) EAP-E ...