ATMEGA64RZAPV-10MU Atmel, ATMEGA64RZAPV-10MU Datasheet - Page 2

BUNDLE ATMEGA644P/AT86RF230 QFN

ATMEGA64RZAPV-10MU

Manufacturer Part Number
ATMEGA64RZAPV-10MU
Description
BUNDLE ATMEGA644P/AT86RF230 QFN
Manufacturer
Atmel
Series
ATMEGAr
Datasheet

Specifications of ATMEGA64RZAPV-10MU

Frequency
2.4GHz
Modulation Or Protocol
802.15.4 Zigbee
Power - Output
3dBm
Sensitivity
-101dBm
Voltage - Supply
1.8 V ~ 3.6 V
Data Interface
PCB, Surface Mount
Memory Size
64kB Flash, 2kB EEPROM, 4kB RAM
Antenna Connector
PCB, Surface Mount
Package / Case
64-QFN
Wireless Frequency
2.4 GHz
Interface Type
SPI, USART
Output Power
3 dBm
For Use With
ATSTK600-TQFP32 - STK600 SOCKET/ADAPTER 32-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Operating Temperature
-
Applications
-
Data Rate - Maximum
-
Current - Transmitting
-
Current - Receiving
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
ATmega64
2 Getting Started with the ATAVRRZ502 Accessory Kit
2.1 Unpacking the System
2.2 System Requirements
2.3 Quick Start Guide
2
AVR414
This section gives an introduction to what the ATAVRRZ502 Accessory Kit contains
and its system requirements. At the end brief instructions are given on how to get the
Accessory Kit up and running in the shortest amount of time.
Kit contents:
• (2 pcs) RZ502 Radio boards with SMA stub antennas.
• (2 pcs) ATmega1281V AVR
• Technical Library CD.
The minimum hardware and software requirements are:
• (2 pcs) STK®500
• (2 pcs) STK501
• (2 pcs) 9 pin RS-232 cable
• (2 pcs) 6-wire cable
• (2 pcs) 2-wire cable
• Power Supply for STK500.
• PC running AVR Studio
This section goes through how to get the RZ502 kit and evaluation application up and
running in the shortest amount of time.
1. Unpack the ATAVRRZ502 Accessory Kit and ensure that it contains all
2. Ensure that all the components listed in subsection 2.2 is available.
3. Go through the steps in section 4 to assemble the hardware. Repeat this step twice
4. Generate EEPROM file for each peer in the network using the HEXMaker
5. Program the ATmega1281 microcontroller by following the instructions in
6. Finally, a chat client is available to interface with the evaluation application just
components listed in subsection 2.1.
to build both peers.
application. How to use this application is described in subsection 5.1.
subsection 5.2. Repeat this step on both peers.
programmed into the AVR microcontroller. Go through the instructions in section 6
on how to setup and use the chat client.
to-RS232 bridge).
®
and with two available RS-232 ports (COM port or USB-
®
microcontroller in TQFP Package.
8051A-AVR-11/06

Related parts for ATMEGA64RZAPV-10MU