ATMEGA128RZAV-8AU Atmel, ATMEGA128RZAV-8AU Datasheet - Page 35

• Manufacturer Part Number: ATMEGA128RZAV-8AU
• Description: MCU ATMEGA1281/AT86RF230 64-TQFP
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA128RZAV-8AU

• Frequency: 2.4GHz
• Data Rate - Maximum: 2Mbps
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3dBm
• Sensitivity: -101dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 4kB EEPROM, 8kB RAM
• Antenna Connector: PCB, Surface Mount
• Package / Case: 64-TQFP
• Wireless Frequency: 2.4 GHz
• Interface Type: JTAG, SPI
• Output Power: 3 dBm
• Operating Temperature Range: - 40 C to + 85 C
• For Use With: 770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEMATSTK501 - ADAPTER KIT FOR 64PIN AVR MCUATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Current - Transmitting: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With/related Products: ATmega128

11.3
11.4
11.5
11.6
2549MS–AVR–09/10
Rev. 2549K-01/07
Rev. 2549J-09/06
Rev. 2549I-07/06
Rev. 2549H-06/06
1.
2.
3.
4.
5.
6:
7.
8.
9.
10.
1.
2.
3.
4.
5.
6.
1.
2.
3.
1.
2.
3.
Updated
Updated
Updated
Updated
Updated Assembly code example in
after setting the ACBG bit or enabling the ADC, the user must always
allow the reference to start up before the output from the Analog Compar-
ator or ADC is used. To reduce power consumption in Power-down mode,
the user can avoid the three conditions above to ensure that the reference
is turned off before entering Power-down mode.” on page
Updated
Updated Bit description in
on page
Updated code example in
Updated
Updated
Updated
Updated code example in
Boot Section” on page
Updated
Updated
Updated
Updated
Added
Updated
page
page
on page
Updated
Updated
Updated
Added
160,
131,
“Data Retention” on page
Table 30-1 on page
116.
189.
Table 1-1 on page
“Pin Descriptions” on page
“Stack Pointer” on page
“Bit 1 – EEPE: EEPROM Programming Enable” on page
“EIMSK – External Interrupt Mask Register” on page
Figure 25-8 on page
“DC Characteristics” on page
“” on page
“Timer/Counter Prescaler” on page
“Device Identification Register” on page
“Signature Bytes” on page
“Instruction Set Summary” on page
“Fast PWM Mode” on page
“” on page
“OSCCAL – Oscillator Calibration Register” on page
Table 15-3 on page
Table 19-3 on page
Table 16-2 on page
46.
46.
109.
ATmega640/1280/1281/2560/2561
“USART Initialization” on page
371.
“Moving Interrupts Between Application and
“PCIFR – Pin Change Interrupt Flag Register”
3.
284.
129,
187,
148,
11.
16.
Table 15-6 on page
Table 19-6 on page 188
Table 16-4 on page
338.
“Thus, when the BOD is not enabled,
150.
7.
367.
186.
415.
303.
130,
159,
210.
63.
and
Table 15-8 on
Table 16-5 on
115.
50.
Table 19-8
36.
35