F2M03ALA-S01 Free2Move, F2M03ALA-S01 Datasheet
F2M03ALA-S01
Specifications of F2M03ALA-S01
Related parts for F2M03ALA-S01
F2M03ALA-S01 Summary of contents
Page 1
... Handheld, laptop and desktop computers • Mobile phones BLUETOOTH is a trademark owned by Bluetooth SIG, Inc., U.S.A. and licensed to Free2move Low power Audio Bluetooth™ Module with antenna F2M03ALA Datasheet General Description F2M03ALA Bluetooth™ v2.1+EDR audio module with an on board antenna, integrated audio codec and amplifier. The module fully Bluetooth™ ...
Page 2
... Low power Audio Bluetooth™ Module with antenna F2M03ALA Table of contents 1 Device pinout .........................................................................................................................3 2 Device terminal functions .....................................................................................................4 3 Electrical Characteristics ......................................................................................................5 3.1 Power Consumption........................................................................................................................ 7 4 Radio Characteristics ............................................................................................................8 5 Firmware versions .................................................................................................................9 5.1 Wireless UART ............................................................................................................................. 11 5.2 HCI ................................................................................................................................................ 16 6 Device terminal description ................................................................................................19 6.1 Mono Audio Interface.................................................................................................................... 19 6 ...
Page 3
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 1 Device pinout GND 1 SPKR- 2 SPKR+ 3 MIC- 4 MIC+ AUX_DAC 5 6 AIO[0] 7 GND 8 RTS CTS 11 VDD 12 Pinout of the F2M03ALA seen from the component side [TOP VIEW] Datasheet NC NC SPI_MOSI SPI_MISO © 2007 Free2move GND 34 33 GND PIO[ PIO[2] PIO[ PIO[8] 28 RESET SPI_CSB 24 ...
Page 4
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 2 Device terminal functions Power supply Pin GND 7, 13, 33, 34 36,37,38,39 VDD 12 Analog I/O Pin AUX_DAC 5 AIO(0) 6 Test and debug Pin RESET 28 SPI_MISO 26 SPI_CSB 25 SPI_CLK 24 SPI_MOSI 27 UART Pin UART_CTS 11 UART_TX 10 UART_RTS 8 UART_RX 9 PCM ...
Page 5
... Storage Temperature Breakdown supply voltage Recommended Operating Conditions* Rating Operating temperature range Supply voltage *F2M03ALA meet the Bluetooth v2.1+EDR specification when used in the recommended operating condition. Digital Terminals Digital Terminals Input Voltage input logic level low, 2.7V ≤ VDD ≤ 3.0V V ...
Page 6
... Low power Audio Bluetooth™ Module with antenna F2M03ALA Auxiliary ADC Auxiliary ADC, 8-bit resolution Resolution Input voltage range (LSB size = 1.8/255= 7.1mV) Accuracy INL (Guaranteed monotonic) DNL Offset Gain Error Input Bandwidth Conversion time Sample rate* *The ADC is accessed through the VM function. The sample rate given is achieved as a part of this function ...
Page 7
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 3.1 Power Consumption Typical Average Current Consumption VDD=3.1V Temperature = +20°C Operation Mode Page scan Inquiry and page scan ACL No traffic ACL With file transfer ACL No traffic ACL With file transfer ACL 40ms sniff ACL 1 ...
Page 8
... Drift (single slot packet) Drift (five slot packet) Note: The F2M03ALA has a maximum transmit power of +4dBm and is certified according to the Bluetooth v2.1+EDR specification as a Class2 device though possible to restrict the maximum transmit power to comply with a Class3 device upon configuration. Bluetooth Specification ...
Page 9
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 5 Firmware versions F2M03 is supplied with Bluetooth stack firmware, which runs on the internal RISC micro controller of the Bluetooth module. This chapter includes an overview of the different options for more in depth information please use separate firmware datasheets provided by Free2move. ...
Page 10
... Low power Audio Bluetooth™ Module with antenna F2M03ALA Application Bluetooth stack HCI Host F2M03 HCI LINK MANAGER BASEBAND and RF HCI, (Two-Processor Architecture) Wireless UART Free2move’s Wireless UART (WU) firmware is intended to replace the serial cable(s) connecting portable and/or fixed electronic devices. Key features are robustness, high configurability, high security, low complexity and low power ...
Page 11
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 5.1 Wireless UART Free2move’s Wireless UART (WU) firmware is intended to replace the serial cable(s) connecting portable and/or fixed electronic devices. Key features are robustness, high configurability, high security, low complexity and low power. ...
Page 12
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 5.1.1 General I/O General I/O interfaces are used for different purposes between the WU firmware and the Host: • Asynchronous data interface – configuration of the WU firmware or exchange transparent digital information between the connected Bluetooth devices. ...
Page 13
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 5.1.2 Settings The default settings allow the user to communicate via Bluetooth, without sending any configuration commands, as soon as a successful connection has been established. Information sent and received on the serial interface of the WU unit at 38400 bps is transmitted transparently between the two connected devices ...
Page 14
... Low power Audio Bluetooth™ Module with antenna F2M03ALA Software / Hardware Reboot This option gives the ability to be able to reboot the module via software commands. Inquiry Search for other Bluetooth devices in the neighborhood. There are three configuration parameters: • How many seconds the search should be active • ...
Page 15
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 5.1.3 Performance The WU firmware is a complete on-chip application; limited resources restrict the maximum throughput. The table below shows the maximum achieved throughput when streaming data between two connected WU v4.00 devices at close range. ...
Page 16
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 5.2 HCI In this implementation the internal processor of the module runs the Bluetooth stack up to the Host Controller Interface (HCI) as specified in the Bluetooth specification V1.1. The external host processor must provide all upper Bluetooth stack layers. Free2move do not offer a host stack solution for an external Host. ...
Page 17
... Low power Audio Bluetooth™ Module with antenna F2M03ALA • Standard Bluetooth power saving mechanisms: Hold, Sniff and Park modes, including “Forced Hold” • Dynamic control of peers’ transmit power via LMP • Master/Slave switch • Broadcast • Channel quality driven data rate (CQDDR) • ...
Page 18
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 5.2.2 Extra Functionality The firmware extends the standard Bluetooth functionality with the following features: • Supports BlueCore Serial Protocol (BCSP proprietary, reliable alternative to the standard Bluetooth (H4) UART Host Transport. • Provides a set of approximately 50 manufacturer-specific HCI extension commands. This command set (called BCCMD – ...
Page 19
... A bias network is required for operation with a microphone whereas the line input may be simply AC coupled. The following sections explain each of these modes. Single ended signals are supported by F2M03ALA: a single ended signal may be driven into either MIC N or MIC_P with the undriven input coupled to ground by a capacitor. ...
Page 20
... It may be obtained by filtering the output of a PIO line. (Subject to firmware support, consult available application notes and datasheets or contact free2move) 6.1.3 Line Input If the input gain is set to less than 21 dB F2M03ALA automatically selects line input mode. In this mode the input impedance at MIC N and MIC _ maximum input signal level is 380 mV rms ...
Page 21
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 6.1.4 Output stage The digital data is converted to an analogue value by a DAC, then it is filtered prior to amplification by the output amplifier and it is available as a differential signal between SPKR P and SPKR N. The output amplifier is capable of driving a speaker directly if its impedance is greater than 8Ω ...
Page 22
... It does not pass through the HCI protocol layer. Hardware on F2M03ALA allows the data to be sent to and received from a SCO connection three SCO connections can be supported by the PCM interface at any one time F2M03ALA can operate as the PCM interface Master generating an output clock of 128, 256 or 512kHz. ...
Page 23
... PCM Interface Master/Slave When configured as the Master of the PCM interface, F2M03ALA generates PCM_CLK and PCM_SYNC. F2M03ALA as PCM Interface Master When configured as the Slave of the PCM interface, F2M03ALA accepts PCM_CLK rates up to 2048kHz F2M03ALA as PCM Interface Slave Datasheet © 2007 Free2move AB ...
Page 24
... In Short Frame Sync the falling edge of PCM_SYNC indicates the start of the PCM word. PCM_SYNC is always one clock cycle long. As with Long Frame Sync, F2M03ALA samples PCM_IN on the falling edge of PCM_CLK and transmits PCM_OUT on the rising edge. PCM_OUT may be configured to be high impedance on the falling edge of ...
Page 25
... The voice sample format is 8-bit companded. As for the standard PCM interface SCO connections can be carried over the first four slots. The start of frame is indicated by PCM SYNC and runs at 8kHz. With F2M03ALA in Slave mode, the frequency of PCM_CLK can 4.096MHz. In order to configure the PCM interface to work in GCI ...
Page 26
... Motorola CODECs. 6.2.7 Additional Features F2M03ALA has a mute facility that forces PCM_OUT Master mode, PCM_SYNC may also be forced to 0 while keeping PCM_CLK running which some CODECS use to control power-down. Datasheet © ...
Page 27
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 6.2.8 PCM Timing Information PCM Master Timing Symbol PCM_CLK f mclk frequency - PCM_SYNC frequency (1) t PCM_CLK high mclkh ( PCM_CLK low mclk - PCM_CLK jitter Delay time from PCM_CLK high to t dmclksynch PCM_SYNC high Delay time from PCM_CLK high to valid ...
Page 28
... Low power Audio Bluetooth™ Module with antenna F2M03ALA PCM Slave Timing Symbol f PCM clock frequency (Slave mode: input) sclk f PCM clock frequency (GCI mode) sclk t PCM_CLK low time sclkl t PCM_CLK high time sclkh Hold time from PCM_CLK low to t hsclksynch ...
Page 29
... Low power Audio Bluetooth™ Module with antenna F2M03ALA PCM slave timing © 2007 Free2move AB Datasheet Rev: a Page 29(51) ...
Page 30
... RS232 standard Four signals are used to implement the UART function, as shown in the figure above. When F2M03ALA is connected to another digital device, UART_RX and UART_TX transfer data between the two devices. The remaining two signals, UART_CTS and UART_RTS, can be used to implement RS232 hardware flow control where both are active low indicators ...
Page 31
... Free2move firmware a reset will occur. This feature allows a host to initialise the system to a known state. Also, the F2M03ALA can emit a Break character that may be used to wake the Host. The above capabilities are not supported in the standard firmware, please contact Free2move for more information ...
Page 32
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 6.4 USB Interface F2M03 contain a full-speed (12Mbits/s) USB interface, capable of driving a USB cable directly. No external USB transceiver is required. The device operates as a USB peripheral, responding to requests from a master host controller such as a PC. Both the OHCI and the UHCI standards are supported. The set of USB endpoints implemented behave as specified in the USB section of the Bluetooth specification v2 ...
Page 33
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 6.4.5 Bus-Powered Mode In bus-powered mode the application circuit draws its current from the 5V VBUS supply on the USB cable. F2M03 negotiates with the PC during the USB enumeration stage about power consumption. Bus-Powered mode is not supported in the default firmware of the HCI-firmware When selecting a regulator, be aware that VBUS may go as low as 4 ...
Page 34
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 6.4.6 Suspend Current USB devices that run off VBUS must be able to enter a suspended state, whereby they consume less that 0.5mA from VBUS. The voltage regulator circuit itself should draw only a small quiescent current (typically less than 100µ ...
Page 35
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 6.4.9 USB 1.1 Compliance The Bluetooth chip on the F2M03 is qualified to the USB specification v1.1, details of which are available from http://www.usb.org. The specification contains valuable information on aspects such as PCB track impedance, supply inrush current and product labeling. ...
Page 36
... Serial Peripheral Interface F2M03ALA is a slave device that uses terminals SPI_MOSI, SPI_MISO, SPI_CLK and SPI_CSB. This interface is used for program emulation/debug and IC test also the means by which the F2M03ALA flash may be programmed, before any 'boot' program is loaded. The SPI signals should be routed out from the module if you need to upgrade the firmware on the module in the future when the module is already soldered ...
Page 37
... PIOs The F2M03ALA have 8 programmable general-purpose I/O ports PIO[9:2] and one analog I/O port AIO[0]. The F2M03ALA also has one digital to analog port AUX_DAC. PIO lines is configured through software to have either weak or strong pull-ups or pull-downs. All PIO lines are configured as inputs with weak pull-downs at reset. ...
Page 38
... Reset The F2M03ALA has an active low reset (pin nr: 28). The reset pin MUST be connected to either a reset- circuit (voltage monitor) such as the TC1270AS, MAX811S, DS1818 or using an I/O from a microcontroller. Reset cannot be done with a R-C network recommended to used one of the reset circuits mentioned above. Special considerations must be taken when using an I/O from a microcontroller ...
Page 39
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 7 Application information and integration manual 7.1 Recommended land pattern The module uses bottom pads for soldering optimized for an automatic solder line also possible to solder the module manually by using hot air soldering. For manual soldering solder pads may in some situation be made slightly larger to allow easier warm up process ...
Page 40
... When using multilayer PCB, through plating is necessary. • Other components may be placed on shaded area Ground Top layer Low power Audio Bluetooth™ Module with antenna F2M03ALA Vias Ground Antenna Top layer Ground Bot layer Ground Top layer © 2007 Free2move AB Datasheet ...
Page 41
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 7.3 Certification considerations The F2M03ALA module has been tested and found compliant to the essential requirements of the R&TTE directive 1999/5/EC. All possible testing on a modular level has been performed. However, for every end product that contains the module, due to the specific product design, additional requirements might become applicable. These are typically EMC, Safety and partly Radio requirements. The end product manufacturer has to ensure, that the essential requirements of the R& ...
Page 42
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 7.4 Typical application schematic F2M03ALA Typical application schematic for F2M03ALA when using the Wireless UART firmware Datasheet © 2007 Free2move AB Rev: a Page 42(51) ...
Page 43
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 8 Package information F2M03ALA Physical size [mm]: Length: 24.0 Width: 13.0 Height: 2.1 Weight: TBD Datasheet (Top and side view) 24 © 2007 Free2move AB Rev: a Page 43(51) ...
Page 44
... F2M03ALA has passed the Bluetooth Qualification/Certification process as specified within the Bluetooth Specifications V2.1/2.1+EDR and as required within the PRD 2.0. QDID: B014393 9.2 CE F2M03ALA complies with the requirements of R&TTE Directive 1999/5/CE, the European Community Directive 73/23/EEC and 93/68/EEC. • EN 300 328 • ...
Page 45
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 9.3 FCC FCC-B Radio Frequency Interference Statement This deceive has been tested and found to comply with the limits for a Class-B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in commercial environment ...
Page 46
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 10 RoHS and WEEE Statement F2M03ALA meets the requirements of Directive 2002/95/EC of the European Parliament and of the Council on the Restriction of Hazardous Substance (RoHS). F2M03ALA also meet the requirements of Directive 2002/96/EG -Waste Electrical and Electronic Equipment (WEEE) ...
Page 47
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 11 Tape and Reel information 11.1 Package Tape dimensions TAPE DETAILS 3.2 24.0 25.0 14.0 Pulling direction 11.2 Reel dimensions A 330.0 max B 1.5 min C 13.0±0.2 D 20.2 min N 100.0 W1 44.4 +2.0 –0.0 W2 50.4 max ...
Page 48
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 12 Ordering information The F2M03ALA is available for ordering. Part nr: F2M03ALA-S01 Low power Bluetooth Audio module with antenna and Wireless UART firmware (SPP) Please visit our website: www.free2move.net Datasheet Description for more information about local distributors and dealers. ...
Page 49
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 13 Document history Date Revision Reason for Change DECEMBER 2008 a First final release, Certification information updated. NOVEMBER 2007 0 First preliminary release, all data within the document are still preliminary Datasheet_F2M03ALA_rev_a.pdf Datasheet F2M03ALA Datasheet ...
Page 50
... Low power Audio Bluetooth™ Module with antenna F2M03ALA 14 Acronyms and definitions Term: Bluetooth A set of technologies providing audio and data transfer over short-range radio ACL Asynchronous Connection-Less. A Bluetooth data packet. AC Alternating Current A-law Audio encoding standard API Application Programming Interface BCSP BlueCore™ ...
Page 51
... Low power Audio Bluetooth™ Module with antenna F2M03ALA Contact information For support questions please contact your local dealer For other purposes use: info@free2move.net Website: www.free2move.net Local dealer/distributor The information given herein includes text, drawings, illustrations and schematics that are believed to be reliable. However, Free2move makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use ...