ATA5773-PXQW Atmel, ATA5773-PXQW Datasheet - Page 67

• Manufacturer Part Number: ATA5773-PXQW
• Description: XMITTR UHF ASK/FSK 310MHZ 24VQFN
• Manufacturer: Atmel

Specifications of ATA5773-PXQW

• Frequency: 310MHz ~ 350MHz
• Modulation Or Protocol: UHF
• Power - Output: 8dBm
• Voltage - Supply: 2 V ~ 4 V
• Current - Transmitting: 9.8mA
• Data Interface: PCB, Surface Mount
• Memory Size: 4kB Flash, 256B EEPROM, 256B SRAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 24-VQFN Exposed Pad, 24-HVQFN, 24-SQFN, 24-DHVQFN
• Processor Series: ATA5x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 4 KB
• Data Ram Size: 256 B
• Interface Type: SPI, USI
• Maximum Clock Frequency: 4 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Applications: -
• Sensitivity: -
• Data Rate - Maximum: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Details

9137E–RKE–12/10
Table 4-22.
The following subsections shortly describe the alternate functions for each port, and relate the
overriding signals to the alternate function. Refer to the alternate function description for fur-
ther details.
Signal Name
PUOE
PUOV
DDOE
DDOV
PVOE
PVOV
PTOE
DIEOE
DIEOV
DI
AIO
Generic Description of Overriding Signals for Alternate Functions
Full Name
Pull-up Override
Enable
Pull-up Override
Value
Data Direction
Override Enable
Data Direction
Override Value
Port Value
Override Enable
Port Value
Override Value
Port Toggle
Override Enable
Digital Input
Enable Override
Enable
Digital Input
Enable Override
Value
Digital Input
Analog
Input/Output
Description
If this signal is set, the pull-up enable is controlled by the
PUOV signal. If this signal is cleared, the pull-up is enabled
when {DDxn, PORTxn, PUD} = 0b010.
If PUOE is set, the pull-up is enabled/disabled when PUOV is
set/cleared, regardless of the setting of the DDxn, PORTxn,
and PUD Register bits.
If this signal is set, the Output Driver Enable is controlled by
the DDOV signal. If this signal is cleared, the Output driver is
enabled by the DDxn Register bit.
If DDOE is set, the Output Driver is enabled/disabled when
DDOV is set/cleared, regardless of the setting of the DDxn
Register bit.
If this signal is set and the Output Driver is enabled, the port
value is controlled by the PVOV signal. If PVOE is cleared,
and the Output Driver is enabled, the port Value is controlled
by the PORTxn Register bit.
If PVOE is set, the port value is set to PVOV, regardless of the
setting of the PORTxn Register bit.
If PTOE is set, the PORTxn Register bit is inverted.
If this bit is set, the Digital Input Enable is controlled by the
DIEOV signal. If this signal is cleared, the Digital Input Enable
is determined by MCU state (Normal mode, sleep mode).
If DIEOE is set, the Digital Input is enabled/disabled when
DIEOV is set/cleared, regardless of the MCU state (Normal
mode, sleep mode).
This is the Digital Input to alternate functions. In the figure, the
signal is connected to the output of the schmitt-trigger but
before the synchronizer. Unless the Digital Input is used as a
clock source, the module with the alternate function will use its
own synchronizer.
This is the Analog Input/Output to/from alternate functions.
The signal is connected directly to the pad, and can be used
bi-directionally.
Atmel ATA5771/73/74
67