A11205RNCQ C&K Components, A11205RNCQ Datasheet - Page 5
![SWITCH ROTARY SP 12POS 2.5A PCB](/photos/15/15/151598/a11205rncq_sml.jpg)
A11205RNCQ
Manufacturer Part Number
A11205RNCQ
Description
SWITCH ROTARY SP 12POS 2.5A PCB
Manufacturer
C&K Components
Series
Ar
Datasheet
1.767B00201.pdf
(5 pages)
Specifications of A11205RNCQ
Number Of Positions
12
Number Of Decks
1
Number Of Poles Per Deck
1
Circuit Per Deck
SP12T
Contact Rating @ Voltage
2.5A @ 125VAC
Actuator Type
Flatted (6.35mm dia)
Mounting Type
Panel, PCB Through Hole
Termination Style
PC Pin
Orientation
Vertical
Angle Of Throw
30°
Contact Form
SP
Contact Material
Silver
Dielectric Strength
1000 Volts
Voltage Rating
125 Volts
Current Rating
2.5 Amps, 350 mAmps at 125 Volts
Actuator
Rotary
Contact Rating
2.5 Amps, 350 mAmps at 125 Volts
Voltage Rating Ac
125 Volts
Voltage Rating Dc
125 Volts
Total # Of Positions
12
Pole Throw Configuration
SP
Actuator Style
Shaft
Actuator Material
Glass/Nylon 6/6
Current Rating (max)
2.5A
Illumination Type
Not Required
Ac Voltage Rating (max)
125VVAC
Dc Voltage Rating (max)
125VVDC
Contact Plating
Silver
Housing Material
N/A/(Glass/Nylon 6/6)
Product Height (mm)
35.19mm
Product Depth (mm)
26.19mm
Product Length (mm)
26.19mm
Operating Temp Range
-30C to 85C
Mounting Style
Panel Mount/Through Hole
Terminal Type
PC Pins
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*A11205RNCQ
A11205RNCQ
CKN6042
A11205RNCQ
CKN6042
Setting Stops on A112 and A125 Models
The number of switch positions is adjustable on A112
and A125 models only by means of a stop ring provided
with each switch. The number of positions is pre-set on
all other models and the stop ring is factory installed.
Soldering, Cleaning and Assembly Instructions for ‘MC’ Termination Option
Soldering
1. Insert switch base only into PC board.
2. Do not bend terminals.
3. Wave soldering recommended at
4. Hand solder at 500F, 10 sec.
Switch Assembly
1. Hold housing/shaft assembly by housing. Remove
2. Do not push on switch shaft. Detent mechanism will
3. While holding switch housing, align locating tab on
4. Push firmly on housing until latches snap in place.
5. Remove clip from shaft and discard. Assembly is
Stop ring
PART NO.
767B00201
Material: Brass
Finish: Nickel plated
NONE
500F solder temperature.
max./terminal.
protective cap by squeezing tabs and discard. (FIG. 1)
come apart.
base with notch on housing and engage 4 housing
latches in slots on base. (FIG. 2)
complete. (FIG. 3)
NO SEAL
E
EPOXY SEAL
FUNCTION
AVAILABLE HARDWARE
F
SPLASHPROOF BUSHING SEAL
K–7
Cleaning
1. Flux clean using vapor degreaser and forced
2. Do not allow switch base to ‘trap’ fluids.
3. Freon TMC, TF or Methylene Chloride give
To set stops: Turn shaft fully counter-clockwise and
insert stop ring tab in desired hole. Install lockwasher
and nut to retain stop ring for both PC and panel
mounting. Switch without stop ring has 12 positions.
rinse or triple bath method.
excellent results.
SPLASHPROOF
BUSHING SEAL
(FIG. 1)
1-4 Pole Rotary Switches
REMOVABLE CLIP
K
EPOXY & SPLASHPROOF BUSHING SEAL
Specifications and dimensions subject to change
(FIG. 2)
www.ck-components.com
LOCATING
Dimensions are shown: mm
STANDOFF
A Series
TAB
(FIG. 3)
K