D2F-01L Omron, D2F-01L Datasheet - Page 6

• Manufacturer Part Number: D2F-01L
• Description: LEVER SWITCH PCB SPDT .1A 80GF
• Manufacturer: Omron
• Series: D2Fr
• Type: Snap Actionr

Specifications of D2F-01L

• Circuit: SPDT
• Switch Function: On-Mom
• Contact Rating @ Voltage: 0.1A @ 30VDC
• Actuator Type: Lever, Straight
• Mounting Type: Through Hole
• Termination Style: PC Pin
• Operating Force: 80gf
• Contact Form: SPDT
• Contact Rating: 0.1 Amp
• Actuator: Lever, Hinge
• Microswitch Type: Ultra Subminiature
• Actuator Style: Hinge Lever
• Operating Force Max: 80gf
• Contact Voltage Ac Nom: 125V
• Contact Voltage Dc Nom: 30V
• Contact Current Max: 100mA
• Body Style: Ultra Subminiature
• Brand/series: D2F-01 Series
• Current, Rating: 0.1 A
• Dielectric Strength: 1500 VAC
• Mounting Hole Size: 1.2 mm
• Number Of Poles: 1
• Operation: Snap Action
• Standards: UL Listed, CSA Certified
• Temperature, Operating: -25 to +65 °C
• Termination: Through Hole
• Voltage, Rating: 30 VDC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: D2F01L; SW154

Precautions
Be sure to read the precautions and information common to all Snap Action and Detection Switches, contained in the Technical User’s Guide,
“Snap Action Switches, Technical Information” for correct use.
■ Correct Use
Mounting
Turn OFF the power supply before mounting or removing the switch,
wiring the switch, or performing maintenance or inspection. Failure to
do so may result in electric shock or burning.
Mount the switch onto a flat surface. Mounting on an uneven surface
may cause deformation of the switch, resulting in faulty operation or
breakage of the housing.
Allow sufficient insulation distance between terminals, terminal
traces and between terminals and ground.
Operating Stroke Setting
Take particular care in setting the operating stroke for the pin plunger
models. Make sure that the operating stroke is 70% to 100% of the
rated OT distance. Do not operate the actuator exceeding the OT
distance, otherwise the service life of the switch maybe decreased.
Using Microloads
Using a model for ordinary loads to switch microloads may result in
faulty operation. Instead, use the models that are designed for micro-
loads and that operate in the following range;
However, even when using microload models within the operating
range shown above, if inrush current or inductive voltage spikes
occur when the contact is opened or closed, it may increase contact
wear and so decrease the service life. Therefore, insert a contact
protection circuit where necessary.
36
Snap Action Switch
Inoperable
range
Operating range
for micro load
models D2F-01
D2F
Current (mA)
Operating
range for
general-load
models
D2F
■ Cautions
Terminal Connection
When soldering a lead wire to the terminal, first insert the lead wire
conductor into the terminal hole and then perform soldering.
Make sure that the capacity of the soldering iron is 30 W maximum
and that the temperature of the soldering tip is approximately 300 °C.
(350 °C maximum.) Complete soldering within 3 s. After soldering,
do not apply external force to the soldered area for about 1 minute.
Using a switch with improper soldering may result in abnormal heat-
ing, possibly resulting in a burn.
Applying the soldering iron for more than 3 s or using an iron that is
rated for more than 30 W may deteriorate the switch characteristics.
When soldering the lead wire to the PCB terminal, pay careful
attention so that the flux and solder liquid level does not exceed the
PCB level.