AFBR-57R5AEZ Avago Technologies US Inc., AFBR-57R5AEZ Datasheet - Page 3
![Fiber Optic Transmitters, Receivers, Transceivers Transceiver](/photos/15/67/156703/afbr-57r5p-afct-57r5tp_wht_sml.jpg)
AFBR-57R5AEZ
Manufacturer Part Number
AFBR-57R5AEZ
Description
Fiber Optic Transmitters, Receivers, Transceivers Transceiver
Manufacturer
Avago Technologies US Inc.
Series
-r
Datasheet
1.AFBR-57R5AEZ.pdf
(20 pages)
Specifications of AFBR-57R5AEZ
Product
Transceiver
Data Rate
4.25 GBd, 2.125 GBd, 1.0625 GBd
Wavelength
860 nm (Max)
Maximum Rise Time
0.09 ns/0.15 ns
Maximum Fall Time
0.09 ns/0.15 ns
Pulse Width Distortion
0.06 ns (Max)/0.062 ns (Max)
Maximum Output Current
300 mA
Operating Supply Voltage
2.97 V to 3.63 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 10 C
Package / Case
SFP
Mounting Type
SFP
Voltage - Supply
2.97 V ~ 3.63 V
Connector Type
LC Duplex
Applications
Ethernet
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
Multimode Fiber
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AFBR-57R5AEZ
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Figure 1. Transceiver functional diagram.
Transmitter Section
The transmitter section consists of the Transmitter Optical
SubAssembly (TOSA) and laser driver circuitry. The TOSA,
containing an 850 nm VCSEL (Vertical Cavity Surface
Emitting Laser) light source, is located at the optical
interface and mates with the LC optical connector. The
TOSA is driven by a custom IC which uses the incoming
differential high speed logic signal to modulate the laser
diode driver current. This Tx laser driver circuit regulates
the optical power at a constant level provided the
incoming data pattern is dc balanced (8B/10B code, for
example).
Transmit Disable (Tx_Disable)
The AFBR-57R5AEZ accepts a TTL and CMOS compat-
ible transmit disable control signal input (pin 3) which
shuts down the transmitter optical output. A high signal
implements this function while a low signal allows
normal transceiver operation. In the event of a fault (e.g.
eye safety circuit activated), cycling this control signal
resets the module as depicted in Figure 4. An internal
pull up resistor disables the transceiver transmitter until
the host pulls the input low. Host systems should allow
a 10 ms interval between successive assertions of this
control signal. Tx_Disable can also be asserted via the
two-wire serial interface (address A2h, byte 110, bit 6)
and monitored (address A2h, byte 110, bit 7).
The contents of A2h, byte 110, bit 6 are logic OR’d with
hardware Tx_Disable (pin 3) to control transmitter
operation.
3
OPTICAL INTERFACE
LIGHT FROM FIBER
LIGHT TO FIBER
RECEIVER
TRANSMITTER
PHOTO-DETECTOR
VCSEL
CONTROLLER & MEMORY
AMPLIFICATION
& QUANTIZATION
Transmit Fault (Tx_Fault)
A catastrophic laser fault will activate the transmitter
signal, TX_FAULT, and disable the laser. This signal is
an open collector output (pull-up required on the host
board). A low signal indicates normal laser operation
and a high signal indicates a fault. The TX_FAULT will
be latched high when a laser fault occurs and is cleared
by toggling the TX_DISABLE input or power cycling the
transceiver. The transmitter fault condition can also be
monitored via the two-wire serial interface (address A2,
byte 110, bit 2).
Eye Safety Circuit
The AFBR-57R5AEZ provides Class 1 (single fault tolerant)
eye safety by design and has been tested for compliance
with the requirements listed in Table 1. The eye safety
circuit continuously monitors the optical output power
level and will disable the transmitter upon detecting an
unsafe condition beyond the scope of Class 1 certifica-
tion. Such unsafe conditions can be due to inputs from
the host board (Vcc fluctuation, unbalanced code) or a
fault within the transceiver.
CIRCUITRY
DRIVER &
SAFETY
LASER
RD+ (RECEIVE DATA)
RDÐ (RECEIVE DATA)
Rx LOSS OF SIGNAL
MOD-DEF2 (SDA)
MOD-DEF1 (SCL)
MOD-DEF0
TX_DISABLE
TD+ (TRANSMIT DATA)
TDÐ (TRANSMIT DATA)
TX_FAULT
ELECTRICAL INTERFACE