1253P08-U THAT Corporation, 1253P08-U Datasheet
1253P08-U
Specifications of 1253P08-U
Related parts for 1253P08-U
1253P08-U Summary of contents
Page 1
... Line Receiver ICs THAT 1250, 1253, 1256 APPLICATIONS Pin Name DIP Pin SO Pin Ref Vee 4 4 Sense 5 5 Vout 6 6 Vcc Table 1. 1250-series pin assignments Gain Plastic DIP Plastic 1250P08-U 1250S08-U ±3 dB 1253P08-U 1253S08-U ±6 dB 1256P08-U 1256S08-U Table 2. Ordering information ...
Page 2
... While specific resistor ratios are very closely trimmed, absolute resistance values can vary ±25% from the typical values show n. Input impedance is monitored by lot sampling. 6. Defined with respect to differential gain. 7. Parameter guaranteed over the entire range of power supply and temperature. THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com Page SPECIFICATIONS ...
Page 3
... The 1250-series devices rely upon the inherent matching of silicon-chromium (Si-Cr), thin-film, integrated resistors to achieve common mode rejection ratio and tight gain accuracy. THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com Page Conditions R = 2kΩ ...
Page 4
... CMRR of the devices. For this reason, THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com Page THAT recommends dc-coupling the inputs of the 1250-series devices ...
Page 5
... In+ 100n V EE Figure 4. RFI and supply bypassing THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com Page capacitors should be located within a few inches of the supply pins on these parts, as shown in Figure 4. Selecting a Gain Variation ...
Page 6
... Ref In Figure line receiver THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com Page Applications while attenuating the noise of the line receivers as well. The output noise of a THAT 1256 is -106 dBu. Since there are two of them, and uncorrelated noise ...
Page 7
... In Lo Figure 11. Circuit for audio ADCs with balanced inputs Figure 12. Automated gain control of a balanced signal THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com Page conversion (degrading CMRR) when there are even slight differences in gain between the VCAs ...
Page 8
... Figure 13. -P (DIP) version package outline drawing THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com Page Package Information Neither the lead-frames nor the plastic mold compounds used in the 1250-series contains any ...