AGL030V2-CSG81 Actel, AGL030V2-CSG81 Datasheet - Page 97

• Manufacturer Part Number: AGL030V2-CSG81
• Description: FPGA - Field Programmable Gate Array 30K System Gates IGLOO
• Manufacturer: Actel

Specifications of AGL030V2-CSG81

• Processor Series: AGL030
• Core: IP Core
• Maximum Operating Frequency: 526.32 MHz, 892.86 MHz
• Number Of Programmable I/os: 66
• Supply Voltage (max): 1.575 V
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Development Tools By Supplier: AGL-Icicle-Kit, AGL-Dev-Kit-SCS, Silicon-Explorer II, Silicon-Sculptor 3, SI-EX-TCA, FlashPro 4, FlashPro 3, FlashPro Lite
• Mounting Style: SMD/SMT
• Supply Voltage (min): 1.14 V
• Number Of Gates: 30 K
• Package / Case: CSP-81
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Figure 2-14 • B-LVDS/M-LVDS Multipoint Application Using LVDS I/O Buffers
Figure 2-15 • LVPECL Circuit Diagram and Board-Level Implementation
OUTBUF_LVPECL
R
T
Z
Z
Z
stub
0
0
Receiver
+
R
R
S
B-LVDS/M-LVDS
Bus LVDS (B-LVDS) and Multipoint LVDS (M-LVDS) specifications extend the existing LVDS standard to
high-performance multipoint bus applications. Multidrop and multipoint bus configurations may contain
any combination of drivers, receivers, and transceivers. Actel LVDS drivers provide the higher drive
current required by B-LVDS and M-LVDS to accommodate the loading. The drivers require series
terminations for better signal quality and to control voltage swing. Termination is also required at both
ends of the bus since the driver can be located anywhere on the bus. These configurations can be
implemented using the TRIBUF_LVDS and BIBUF_LVDS macros along with appropriate terminations.
Multipoint designs using Actel LVDS macros can achieve up to 200 MHz with a maximum of 20 loads. A
sample application is given in
section in
Example: For a bus consisting of 20 equidistant loads, the following terminations provide the required
differential voltage, in worst-case Industrial operating conditions, at the farthest receiver: R
R
LVPECL
Low-Voltage Positive Emitter-Coupled Logic (LVPECL) is another differential I/O standard. It requires
that one data bit be carried through two signal lines. Like LVDS, two pins are needed. It also requires
external resistor termination.
The full implementation of the LVDS transmitter and receiver is shown in an example in
building blocks of the LVPECL transmitter-receiver are one transmitter macro, one receiver macro, three
board resistors at the transmitter end, and one resistor at the receiver end. The values for the three driver
resistors are different from those used in the LVDS implementation because the output standard
specifications are different.
-
T
EN
R
Z
= 70 Ω, given Z
S
stub
FPGA
Z
Z
Table 2-148 on page 2-82
Z
0
0
stub
Transceiver
+
R
T
S
0
-
= 50 Ω (2") and Z
N
EN
P
R
Z
stub
S
Bourns Part Number: CAT16-PC4F12
100 Ω
100 Ω
Z
Z
Z
0
0
Figure
stub
Driver
+
R
D
and
S
2-14. The input and output buffer delays are available in the LVDS
stub
-
EN
R
Z
Table 2-149 on page
S
stub
187 W
= 50 Ω (~1.5").
R ev i si o n 1 8
Z
Z
Z
Z
Z
0
0
0
0
stub
= 50 Ω
= 50 Ω
Receiver
+
R
R
S
-
EN
100 Ω
R
Z
S
stub
2-82.
...
N
P
Z
Z
0
0
IGLOO Low Power Flash FPGAs
FPGA
Transceiver
+
–
+
R
T
S
-
EN
INBUF_LVPECL
R
S
Figure
S
BIBUF_LVDS
= 60 Ω and
Z
Z
2-15. The
0
0
2- 83
R
T