PV36W103C01B00 Murata, PV36W103C01B00 Datasheet - Page 5

• Manufacturer Part Number: PV36W103C01B00
• Description: Trimmer Resistors - Multi Turn 10Kohms 10mm Square 25turn
• Manufacturer: Murata

Specifications of PV36W103C01B00

• Resistance: 10 KOhms
• Power Rating: 0.5 Watt (1/2 Watt)
• Operating Temperature Range: - 55 C to + 125 C
• Element Type: Cermet
• Product: Multi-Turn Trimmer Potentiometers
• Tolerance: 10 %
• Number Of Turns: 25
• Taper: Linear
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
!Note
1. Store in temperatures of -10 to +40 deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. If you use the trimmer potentiometer in an
1. When using with partial load (rheostat), minimize
2. The maximum input voltage to a trimmer
3. The maximum input current to a trimmer
1. Soldering
2. Mounting
(1) Standard soldering condition
(2) To minimize mechanical stress when adjusting,
(3) The soldering iron should not come in contact
(1) Use PCB hole to meet the pin of the trimmer
Notice (Operating and Storage Conditions)
relative humidity of 30-85%RH.
environment other than listed below, please
consult with a Murata factory representative prior
to using.
The trimmer potentiometer should not be used under
Notice (Rating)
the power depending on the resistance value.
potentiometer should not exceed (P.R)^1/2 or the
maximum operating voltage, whichever is smaller.
potentiometer should not exceed (P/R)^1/2 or the
allowable wiper current, whichever is smaller.
Notice (Soldering and Mounting)
(a) Flow soldering :
(b) Soldering iron :
Before using other soldering conditions than
those listed above, please consult with Murata
factory representative prior to using. If the
soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature,
the trimmer potentiometer may deviate from the
specified characteristics.
the trimmer potentiometer should be mounted onto
PCB without gap.
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
potentiometer. If the trimmer potentiometer
installs into insufficient PCB hole, the
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
>Pre-heating temp. 80-100 deg. C
>Soldering temp.
>Soldering time
>Temperature of tip 300 deg. C max.
>Soldering time
>Wattage of iron
3 sec. max.
3 sec. max.
260 deg. C max.
40W max.
PV12/PV37/PV23/PV22/PV36 Series Notice
3. Cleaning
(1) Corrosive gaseous atmosphere
(2) In liquid
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
(2) Do not apply excessive force (preferably 9.8N
(1) Isopropyl-alcohol and Ethyl-alcohol are
(2) The total cleaning time by cold dipping, vapor
(3) For ultra-sonic cleaning, the available
the following environmental conditions:
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(Ex. Oil, Medical liquid, Organic solvent, etc.)
trimmer potentimeter may be damaged by
mechanical stress.
(Ref.; 1kgf) max.), when the trimmer
potentiometer is mounted to the PCB.
applicable solvents for cleaning. If you use any
other types of solvents, please consult with a
Murata factory representative prior to using.
and ultrasonic washing (conditions as below)
method should be less than 3 minutes.
condition is as follows.
Due to the ultra-sonic cleaning equipment's
peculiar self-resonance point and that the
cleaning compatibility usually depends on the jig
construction and/or the cleaning condition such
as the depth of immersion, please check the
cleaning equipment to determine the suitable
conditions.
If the trimmer potentiometer is cleaned by
other conditions, the trimmer potentiometer may
be damaged.
>Power: 600W (67 liter) max.
>Frequency: 28kHz
>Temperature: Ambient temperature
R50E13.pdf 04.6.11
71
8