97-3102A-14S-7S Amphenol, 97-3102A-14S-7S Datasheet - Page 4
![Circular MIL / Spec Connectors 14S-7S SOCKETS](/photos/16/70/167087/landingpageamphenol97series_sml.jpg)
97-3102A-14S-7S
Manufacturer Part Number
97-3102A-14S-7S
Description
Circular MIL / Spec Connectors 14S-7S SOCKETS
Manufacturer
Amphenol
Series
97 Seriesr
Datasheet
1.97-79-513-8.pdf
(44 pages)
Specifications of 97-3102A-14S-7S
Mil Type
MIL-DTL-5015
Product Type
Connectors
Contact Style
Socket (Female)
Shell Style
Receptacle
Shell Size
14S-7
Number Of Contacts
3
Mating Style
Receptacle
Mounting Style
Panel
Termination Style
Solder Socket
Contact Type
Socket
Shell Plating
Aluminum Alloy
Contact Plating
Silver
Current Rating
13 A
Voltage Rating
700 V
Body Material
Aluminum Alloy
Mounting Angle
Straight
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Guide to Selecting a Connector
In selecting a connector, it first must be
determined if a non-environmental 97
A or B Series 5015 type is required or if
an environmental MS-5015 Class E, F,
or R type* is required.
If determined that the general duty,
non-environmental 97 series is the
choice - then this catalog is appropriate
to your needs
mulation of a part number.**
1
These two questions are important,
because they indicate which insert you
need. There are literally hundreds to
choose from.
contact connectors are illustrated on
pages 6-11. The inserts most often
used are highlighted on these pages.
an insert arrangement. Say you want to
connect eight 16-ga. wires, - first find
the section of arrangements contain-
ing 8 contacts. Insert number 20-7 is
the one you want because it contains
eight 16-ga. contacts and it is one of
the most often used. The one you
choose might depend on your space or
voltage requirements. The voltage
capacity of each insert is listed under
its diagram.
to connect, the method is essentially
the same. Actually, the insert configu-
rations for multiple-size wires are a lot
more flexible than they appear. That’s
because you can always solder a
smaller wire to a larger contact. How-
ever, soldering a large wire to a small
contact isn’t recommended because of
size and current requirements.
2
Here’s a situation to watch out for. You
have four identical receptacles on a
panel. One carries high current loads.
* If an environmental type MIL-5015 E, F or R Class is required, then the
catalog that should be consulted is 12-020, MS/Standard MIL-5015
Cylindrical Connectors. See www.amphenol-industrial.com for on-line
catalogs or contact Amphenol, Sidney, NY.
The following 8 steps apply to for-
The insert arrangements for solder
Here’s an example of how to choose
If you have more than one wire size
How many wires are you
going to connect?
What gauge?
What if several identical
connectors have different
functions?
The others have low current functions.
A plug mated with the wrong receptacle
(cross-mating) could ruin your valu-
able equipment.
order identical inserts positioned in
both the plugs and receptacles at vari-
ous angles from standard. These varia-
tions from standard position are called
alternate insert positions, and are
described on page 12.
3
For Wall Mounting Use a wall recep-
tacle, type 3100. The elongated back of
this receptacle extends through thick
wall material. It is threaded to accept
standard hardware fittings.
For Unmounted Applications Use
the cable receptacle, type 3101.
For Box or Panel Mounting Use the
box receptacle, type 3102. This recep-
tacle’s back is short to conserve space.
It is not threaded on the back end and
is used when no accessories such as
clamps are needed.
4
For ordinary situations The straight
plug, type 3106 meets most connector
requirements. However . . .
when space is critical you may want
to consider using an angle plug, type
3108. This type plug lets the cable
enter your equipment at a right angle.
5
You can get both straight and angle
plugs in solid or split back shell
designs. With the solid shell you have
greater strength and you save space.
On the other hand, the split shell
design lets you quickly inspect the sol-
der terminals when you need to. This
feature could be important if you’ll be
subjecting the connector to rough han-
dling and heavy use.
shell construction is the letter A. This
designation letter goes immediately
To avoid cross-mating, you can
The designation to use for solid
What kind of receptacle do
you need?
What kind of plug do you
need?
Do you need a plug with a
Solid or Split back shell?
2
** These steps are for solder type connectors which are described in
detail on pages 3-19. If a crimp type connector is needed, the same
steps apply, however, you should consult pages 20-29 for details on 97
Series connectors with crimp contacts.
after the main shell type number: for
example, 3106A or 3108A.
The designation for split shell construc-
tion is the letter B; for example, 3106B
or 3108B.
are made in solid backshell construc-
tion only. Their designation is 3100A,
3101A. (See how to order for solder
contact connectors, page 19.
6
You’re at the point where you desig-
nate which inserts are used with which
shells. Either pin or socket inserts can
be used with plugs or receptacles.
the sockets for the connector at the
“hot” side of the circuit. By having sock-
ets at the power source, there’s little
chance that a wayward finger or screw-
driver will short the circuit or cause per-
sonal injury.
ply S in a part number, following the
insert code number. For pins, the des-
ignation is P. Therefore, the 20-7P
insert would have pin contacts, while
the 20-7S insert would have socket
contacts.
7
If you prefer the standard olive cad-
mium, non-reflective, electrically con-
ductive finish, then no suffix number is
required. Other plating variations are
available,
friendly zinc alloy. See how to order
instructions for the various plating fin-
ishes offered for 97 Series solder con-
nectors on page 19.
8
Accessories - cable clamps, protection
caps and chains, conduit adapters, and
panel gaskets are shown on pages 33-
39.
Because of application, receptacles
Here’s a good rule of thumb. Order
The designation for sockets is sim-
Which connector gets the
socket? - the receptacle or
the plug?
What type of plating is pre-
ferred?
Do you need any
accessories?
including
environmentally