PIC18F45K80-I/PT Microchip Technology, PIC18F45K80-I/PT Datasheet - Page 349

• Manufacturer Part Number: PIC18F45K80-I/PT
• Description: MCU PIC 32KB FLASH 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F45K80-I/PT

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Core Processor: PIC
• Speed: 64MHz
• Connectivity: ECAN, I²C, LIN, SPI, UART/USART
• Number Of I /o: 35
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.6K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP
• Controller Family/series: PIC18
• Ram Memory Size: 4KB
• Cpu Speed: 16MIPS
• No. Of Pwm Channels: 5
• Embedded Interface Type: I2C, SPI, USART
• Processor Series: PIC18F45K80
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 64 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 5
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

22.3
The Asynchronous mode of operation is selected by
clearing the SYNC bit (TXSTAx<4>). In this mode, the
EUSART uses standard Non-Return-to-Zero (NRZ)
format (one Start bit, eight or nine data bits and one Stop
bit). The most common data format is 8 bits. An on-chip,
dedicated 8-bit/16-bit Baud Rate Generator can be used
to derive standard baud rate frequencies from the
oscillator.
The EUSART transmits and receives the LSb first. The
EUSART’s transmitter and receiver are functionally
independent but use the same data format and baud
rate. The Baud Rate Generator produces a clock, either
x16 or x64 of the bit shift rate, depending on the BRGH
and BRG16 bits (TXSTAx<2> and BAUDCONx<3>).
Parity is not supported by the hardware but can be
implemented in software and stored as the 9th data bit.
When operating in Asynchronous mode, the EUSART
module consists of the following important elements:
• Baud Rate Generator
• Sampling Circuit
• Asynchronous Transmitter
• Asynchronous Receiver
• Auto-Wake-up on Sync Break Character
• 12-Bit Break Character Transmit
• Auto-Baud Rate Detection
22.3.1
The EUSART transmitter block diagram is shown in
Figure
(Serial) Shift Register (TSR). The Shift register obtains
its data from the Read/Write Transmit Buffer register,
TXREGx. The TXREGx register is loaded with data in
software. The TSR register is not loaded until the Stop
bit has been transmitted from the previous load. As
soon as the Stop bit is transmitted, the TSR is loaded
with new data from the TXREGx register (if available).
FIGURE 22-3:
 2011 Microchip Technology Inc.
22-3. The heart of the transmitter is the Transmit
EUSART Asynchronous Mode
EUSART ASYNCHRONOUS
TRANSMITTER
BRG16
TXxIE
Interrupt
EUSART TRANSMIT BLOCK DIAGRAM
SPBRGHx
Baud Rate Generator
TXxIF
TXEN
Baud Rate CLK
SPBRGx
MSb
(8)
TXREGx Register
Preliminary
TSR Register
TX9D

TX9
8
Data Bus
PIC18F66K80 FAMILY
Once the TXREGx register transfers the data to the TSR
register (occurs in one T
empty and the TXxIF flag bit is set. This interrupt can be
enabled or disabled by setting or clearing the interrupt
enable bit, TXxIE. TXxIF will be set regardless of the
state of TXxIE; it cannot be cleared in software. TXxIF is
also not cleared immediately upon loading TXREGx, but
becomes valid in the second instruction cycle following
the load instruction. Polling TXxIF immediately following
a load of TXREGx will return invalid results.
While TXxIF indicates the status of the TXREGx regis-
ter; another bit, TRMT (TXSTAx<1>), shows the status
of the TSR register. TRMT is a read-only bit which is set
when the TSR register is empty. No interrupt logic is
tied to this bit so the user has to poll this bit in order to
determine if the TSR register is empty.
To set up an Asynchronous Transmission:
1.
2.
3.
4.
5.
6.
7.
8.
Note 1: The TSR register is not mapped in data
Initialize the SPBRGHx:SPBRGx registers for
the appropriate baud rate. Set or clear the
BRGH and BRG16 bits, as required, to achieve
the desired baud rate.
Enable the asynchronous serial port by clearing
bit, SYNC, and setting bit, SPEN.
If interrupts are desired, set enable bit, TXxIE.
If 9-bit transmission is desired, set transmit bit,
TX9. Can be used as address/data bit.
Enable the transmission by setting bit, TXEN,
which will also set bit, TXxIF.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit, TX9D.
Load data to the TXREGx register (starts
transmission).
If using interrupts, ensure that the GIE and PEIE
bits (INTCON<7:6>) are set.
LSb
0
2: Flag bit, TXxIF, is set when enable bit,
TRMT
memory, so it is not available to the user.
TXEN, is set.
and Control
Pin Buffer
SPEN
CY
), the TXREGx register is
TXx pin
DS39977C-page 349