PVZ3A201C01R00 Murata Electronics North America, PVZ3A201C01R00 Datasheet - Page 46

no-image

PVZ3A201C01R00

Manufacturer Part Number
PVZ3A201C01R00
Description
TRIM POT 200 OHM 3MM TOP ST
Manufacturer
Murata Electronics North America
Series
PVZ3r
Datasheet

Specifications of PVZ3A201C01R00

Resistance (ohms)
200
Termination Style
J Lead
Power (watts)
0.1W, 1/10W
Tolerance
±30%
Temperature Coefficient
±500ppm/°C
Number Of Turns
Single
Adjustment Type
Top Adjustment
Resistive Material
Carbon
Mounting Type
Surface Mount
Package / Case
Square - 0.126" L x 0.122" W x 0.073" H (3.20mm x 3.10mm x 1.85mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
7
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
Soldering profile for Lead-free solder (96.5Sn/3.0Ag/0.5Cu), Eutectic solder (63Sn/37Pb)
1. Use suitable screwdrivers that fit comfortably in
2. Do not apply more than 9.8N (Ref. 1kgf) of twist
1. Please make sure that your product has been
2. Murata cannot guarantee trimmer potentiometer
44
PV12/PV37/PV36 Series Notice
PV12
PV37
PV36
PV12
PV37
PV36
Series
Series
Soldering Profile
Notice (Handling)
driver slot. We recommend the screwdrivers below.
* Recommended screwdriver for manual adjustment
We can supply the screwdrivers above.
If you place order, please specify the Murata P/N.
and stress after mounting onto PCB to prevent
contact intermittence. If excessive force is
applied, the trimmer potentiometer may not
function.
Notice (Other)
evaluated and confirmed against your
specifications when our product is mounted to your
product.
integrity when used under conditions other than
those specified in this document.
Flow Soldering Profile
Soldering Iron
ENGINEER INC.: DA-40
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
(Murata P/N: KMDR180)
Temperature of Soldering Iron Tip
Temp. (T1)
T1
150
C
Pre-heating
Pre-heating
350 10
t1
60 to 120
Time (t1)
C
T3
T2
sec.
Heating
t2
Standard Profile
Temp. (T2)
Time (s)
250
C
Heating
Limit Profile
Standard Profile
Soldering Time
Time (t2)
5 max.
sec.
3 max.
sec.
of Flow
Cycle
Standard Condition
Time
1
3. When adjusting with an adjustment tool, the applied
4. When using a lock paint to fix slot position,
force to the adjustment screw should not exceed
4.9N (Ref. 500gf). If excessive force is applied,
the trimmer potentiometer may not function due to
damage.
please use adhesive resin without chlorine or
sulfur (Three-bond "1401 series") and evaluate
performance with your product. Lock paint may
cause corrosion or electrical contact problems.
Temp. (T1)
Soldering Iron Power Output
150
C
Pre-heating
30 max.
W
60 to 120
Time (t1)
sec.
Limit Profile
Temp. (T3)
260
C
Heating
Cycle of Soldering Iron
Time (t2)
3 max.
sec.
Time
1
of Flow
Cycle
Time
1
R50E.pdf
11.1.17

Related parts for PVZ3A201C01R00