PV32H202A01B00 Murata Electronics North America, PV32H202A01B00 Datasheet - Page 31

• Manufacturer Part Number: PV32H202A01B00
• Description: TRIM POT 2K OHM 6MM TOP ST
• Manufacturer: Murata Electronics North America
• Series: PV32r

Specifications of PV32H202A01B00

• Resistance (ohms): 2K
• Termination Style: PC Pin
• Power (watts): 0.5W, 1/2W
• Tolerance: ±20%
• Temperature Coefficient: ±100ppm/°C
• Number Of Turns: Single
• Adjustment Type: Top Adjustment
• Resistive Material: Ceramic
• Mounting Type: Through Hole
• Package / Case: Round - 0.260" Dia x 0.181" H (6.60mm x 4.60mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Store in temperatures of -10 to +40 deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. If you use the trimmer potentiometer in an
1. When using with partial load (rheostat), minimize
2. The maximum input voltage to a trimmer
1. Soldering
(1) Soldering condition
(2) Cannot be soldered using the flow soldering
(3) The soldering iron should not come in contact
(4) Insufficient amounts of solder can lead to
Notice (Operating and Storage Conditions)
relative humidity of 30-85%.
environment other than listed below, please
consult with a Murata factory representative prior
to using.
The trimmer potentiometer should not be used under
the following environmental conditions:
Notice (Rating)
the power depending on the resistance value.
potentiometer should not exceed (P•R)^1/2 or the
maximum operating voltage, whichever is smaller.
Notice (Soldering and Mounting)
Refer to the temperature profile.
If the soldering conditions are not suitable,
e.g., excessive time and/or excessive
temperature, the trimmer capacitor may deviate
from the specified characteristics.
method. If you use the flow soldering method,
the trimmer potentiometer may not function.
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2. Mounting
3. Cleaning
(1) Corrosive gaseous atmosphere
(2) In liquid
(3) Dusty/dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
(1) Use our standard land dimension. Excessive land
(2) Do not apply excessive force, preferably 9.8N
(3) Do not warp and/or bend PC board to prevent
(4) In chip placers, the recommended size of the
Isopropyl-alcohol and Ethyl-alcohol are applicable
solvents for cleaning. If you use any other types of
solvents, please consult with a Murata factory
representative prior to using.
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(Ex. Oil, Medical liquid, Organic solvent, etc.)
area causes displacement due to the effect of
the surface tension of the solder. Insufficient
land area leads to insufficient soldering strength
of the chip.
max. (Ref. 1kgf) when the trimmer potentiometer
is mounted to the PCB.
trimmer potentiometer from breakage.
cylindrical pick-up nozzle should be outer
dimension 4.0mm dia. and inner dimension 2.0mm
dia.
PVG5 Series Notice
R50E.pdf
29
11.1.17
5