SX1231-31SKB915 Semtech, SX1231-31SKB915 Datasheet - Page 23
SX1231-31SKB915
Manufacturer Part Number
SX1231-31SKB915
Description
TVS
Manufacturer
Semtech
Specifications of SX1231-31SKB915
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 23 of 81
- Download datasheet (2Mb)
3.5.3. Automatic Gain Control
By default (LnaGainSelect = 000), the LNA gain is controlled by a digital AGC loop in order to obtain the optimal sensitivity/
linearity trade-off.
Regardless of the data transfer mode (Packet or Continuous), the following series of events takes place when the receiver
is enabled:
Notes - the AGC procedure must be performed while receiving preamble in FSK mode
The following figure illustrates the AGC behavior:
The following table summarizes the performance (typical figures) of the complete receiver:
Rev 3 - April 2010
ADVANCED COMMUNICATIONS & SENSING
The receiver stays in WAIT mode, until RssiValue exceeds RssiThreshold for two consecutive samples. Its power
consumption is the receiver power consumption.
When this condition is satisfied, the receiver automatically selects the most suitable LNA gain, optimizing the sensitivity/
linearity trade-off.
The programmed LNA gain, read-accessible with LnaCurrentGain in RegLna, is carried on for the whole duration of the
packet, until one of the following conditions is fulfilled:
Packet mode: if AutoRxRestartOn = 0, the LNA gain will remain the same for the reception of the following packet. If
AutoRxRestartOn = 1, after the controller has emptied the FIFO the receiver will re-enter the WAIT mode described
above, after a delay of InterPacketRxDelay, allowing for the distant transmitter to ramp down, hence avoiding a false
RSSI detection.
Continuous mode: upon reception of valid data, the user can decide to either leave the receiver enabled with the same
LNA gain, or to restart the procedure, by setting RestartRx bit to 1, resuming the WAIT mode of the receiver, described
above.
-125 dBm
Towards
- in OOK mode, the AGC will give better results if performed while receiving a constant “1” sequence
Lower Noise Figure
Higher Sensitivity
G1
Lower Linearity
16dB
Figure 7. AGC Thresholds Settings
G2
7dB
Page 23
G3
11dB
G4
9dB
11dB
G5
Higher Noise Figure
Lower Sensitivity
Higher Linearity
DATASHEET
G6
www.semtech.com
SX1231
Pin [dBm]
Related parts for SX1231-31SKB915
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
USB Kit - SX1231 433Mhz
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
development tool usb kit for sx1231 transceiver...
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
Low Power Integrated UHF Transceiver
Manufacturer:
SEMTECH [Semtech Corporation]
Datasheet:
Part Number:
Description:
EVALUATION BOARD
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
EVALUATION BOARD
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
VOLTAGE SUPPRESSOR, TRANSIENT SEMTECH
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
HIGH VOLTAGE CAPACITORS MONOLITHIC CERAMIC TYPE
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
EZ1084CM5.0 AMP POSITIVE VOLTAGE REGULATOR
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
3.0 AMP LOW DROPOUT POSITIVE VOLTAGE REGULATORS
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
RailClamp Low Capacitance TVS Diode Array
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet: