UPD78F0535GB(T)-UEU-A NEC, UPD78F0535GB(T)-UEU-A Datasheet - Page 330
UPD78F0535GB(T)-UEU-A
Manufacturer Part Number
UPD78F0535GB(T)-UEU-A
Description
8BIT MCU, 60K FLASH, 3KB RAM, LQFP
Manufacturer
NEC
Datasheet
1.UPD78F0535GBT-UEU-A.pdf
(773 pages)
Specifications of UPD78F0535GB(T)-UEU-A
Controller Family/series
UPD78
No. Of I/o's
55
Ram Memory Size
3KB
Cpu Speed
20MHz
No. Of Timers
8
No. Of Pwm
RoHS Compliant
Core Size
8bit
Program Memory Size
60KB
Oscillator Type
External, Internal
- Current page: 330 of 773
- Download datasheet (6Mb)
13.6 Cautions for A/D Converter
(1) Operating current in STOP mode
(2) Input range of ANI0 to ANI7
(3) Conflicting operations
(4) Noise countermeasures
330
The A/D converter stops operating in the STOP mode. At this time, the operating current can be reduced by
clearing bit 7 (ADCS) and bit 0 (ADCE) of the A/D converter mode register (ADM) to 0.
To restart from the standby status, clear bit 0 (ADIF) of interrupt request flag register 1L (IF1L) to 0 and start
operation.
Observe the rated range of the ANI0 to ANI7 input voltage. If a voltage of AV
(even in the range of absolute maximum ratings) is input to an analog input channel, the converted value of that
channel becomes undefined. In addition, the converted values of the other channels may also be affected.
<1> Conflict between A/D conversion result register (ADCR, ADCRH) write and ADCR or ADCRH read by
<2> Conflict between ADCR or ADCRH write and A/D converter mode register (ADM) write, analog input
To maintain the 10-bit resolution, attention must be paid to noise input to the AV
<1> Connect a capacitor with a low equivalent resistance and a good frequency response to the power supply.
<2> The higher the output impedance of the analog input source, the greater the influence. To reduce the
<3> Do not switch these pins with other pins during conversion.
<4> The accuracy is improved if the HALT mode is set immediately after the start of conversion.
instruction upon the end of conversion
ADCR or ADCRH read has priority. After the read operation, the new conversion result is written to ADCR
or ADCRH.
channel specification register (ADS), or A/D port configuration register (ADPC) write upon the end of
conversion
ADM, ADS, or ADPC write has priority. ADCR or ADCRH write is not performed, nor is the conversion end
interrupt signal (INTAD) generated.
noise, connecting external C as shown in Figure 13-20 is recommended.
CHAPTER 13 A/D CONVERTER
User’s Manual U17260EJ6V0UD
REF
REF
pin and pins ANI0 to ANI7.
or higher and AV
SS
or lower
Related parts for UPD78F0535GB(T)-UEU-A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
16/8 bit single-chip microcomputer
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual audio power amp circuit
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual comparator
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
MOS type composite field effect transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
50 V/100 mA FET array incorporating 2 N-ch MOSFETs
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Twin transistors equipped with different model chips(6P small MM)
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Bipolar analog integrated circuit
Manufacturer:
NEC
Datasheet: