UPD78F9502MA-CAC-A NEC, UPD78F9502MA-CAC-A Datasheet - Page 82
UPD78F9502MA-CAC-A
Manufacturer Part Number
UPD78F9502MA-CAC-A
Description
8BIT MCU, 4K FLASH, 128B RAM, SMD
Manufacturer
NEC
Datasheet
1.UPD78F9502MA-CAC-A.pdf
(229 pages)
Specifications of UPD78F9502MA-CAC-A
Controller Family/series
UPD78F
No. Of I/o's
8
Ram Memory Size
128Byte
Cpu Speed
10MHz
No. Of Timers
2
No. Of Pwm
RoHS Compliant
Core Size
8bit
Program Memory Size
4KB
Oscillator Type
External, Internal
- Current page: 82 of 229
- Download datasheet (2Mb)
frequency is f
82
(2) Timing chart
If the setting value of the CMP01 register is N, the setting value of the CMP11 register is M, and the count clock
<4> When 8-bit timer counter H1 and the CMP11 register match, TOH1 output becomes inactive and the
<5> By performing procedures <3> and <4> repeatedly, a pulse with an arbitrary duty can be obtained.
<6> To stop the count operation, set TMHE1 = 0.
Cautions 1. In PWM output mode, the setting value for the CMP11 register can be changed during timer
The operation timing in PWM output mode is shown below.
Caution Make sure that the CMP11 register setting value (M) and CMP01 register setting value (N) are
compare register to be compared with 8-bit timer counter H1 is changed from the CMP11 register to the
CMP01 register.
generated.
CNT
within the following range.
00H
2. Be sure to set the CMP11 register when starting the timer count operation (TMHE1 = 1) after
, the PWM pulse output cycle and duty are as follows.
PWM pulse output cycle = (N+1)/f
Duty = Active width : Total width of PWM = (M + 1) : (N + 1)
count operation. However, three operation clocks (signal selected using the CKS12 to
CKS10 bits of the TMHMD1 register) or more are required to transfer the register value after
rewriting the CMP11 register value.
the timer count operation was stopped (TMHE1 = 0) (be sure to set again even if setting the
same value to the CMP11 register).
CMP11 (M) < CMP01 (N)
At this time, 8-bit timer counter H1 is not cleared and the INTTMH1 signal is not
Preliminary User’s Manual U18681EJ1V0UD
CHAPTER 6 8-BIT TIMER H1
FFH
CNT
Related parts for UPD78F9502MA-CAC-A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
16/8 bit single-chip microcomputer
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual audio power amp circuit
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual comparator
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
MOS type composite field effect transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
50 V/100 mA FET array incorporating 2 N-ch MOSFETs
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Twin transistors equipped with different model chips(6P small MM)
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Bipolar analog integrated circuit
Manufacturer:
NEC
Datasheet: