LT3010EMS8E Linear Technology, LT3010EMS8E Datasheet - Page 8
LT3010EMS8E
Manufacturer Part Number
LT3010EMS8E
Description
IC,VOLT REGULATOR,ADJUSTABLE,+1.275 TO +60V,BIPOLAR,TSSOP,8PIN,PLASTIC
Manufacturer
Linear Technology
Series
-r
Datasheet
1.LT3010EMS8E.pdf
(18 pages)
Specifications of LT3010EMS8E
Rohs Compliant
NO
Regulator Topology
Positive Adjustable
Voltage - Output
1.275 V ~ 60 V
Voltage - Input
3 V ~ 80 V
Voltage - Dropout (typical)
0.3V @ 50mA
Number Of Regulators
1
Current - Output
50mA
Current - Limit (min)
60mA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-TSSOP, 8-MSOP (0.118", 3.00mm Width)
Lead Free Status / Rohs Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LT3010EMS8E
Manufacturer:
LT
Quantity:
10 000
Part Number:
LT3010EMS8E
Manufacturer:
LT
Quantity:
20 000
Company:
Part Number:
LT3010EMS8E#PBF
Manufacturer:
LT
Quantity:
12 500
Part Number:
LT3010EMS8E#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LT3010EMS8E#PBF/MP
Manufacturer:
MAX
Quantity:
17
Company:
Part Number:
LT3010EMS8E#TRPBF
Manufacturer:
LT
Quantity:
12 500
Part Number:
LT3010EMS8E#TRPBF
Manufacturer:
LT/凌特
Quantity:
20 000
Part Number:
LT3010EMS8E-5
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LT3010EMS8E-5#PBF
Manufacturer:
LT
Quantity:
1 248
Part Number:
LT3010EMS8E-5#PBF
Manufacturer:
LT/凌特
Quantity:
20 000
PIN FUNCTIONS
LT3010/LT3010-5
OUT (Pin 1): Output. The output supplies power to the load.
A minimum output capacitor of 1µF is required to prevent
oscillations. Larger output capacitors will be required for
applications with large transient loads to limit peak volt-
age transients. See the Applications Information section
for more information on output capacitance and reverse
output characteristics.
SENSE (Pin 2): Sense. For the LT3010-5, the SENSE pin
is the input to the error amplifier. Optimum regulation will
be obtained at the point where the SENSE pin is connected
to the OUT pin of the regulator. In critical applications,
small voltage drops are caused by the resistance (R
PC traces between the regulator and the load. These may
be eliminated by connecting the SENSE pin to the output
at the load as shown in Figure 1 (Kelvin Sense Connec-
tion). Note that the voltage drop across the external PC
traces will add to the dropout voltage of the regulator.
The SENSE pin bias current is 10µA at the nominal rated
output voltage.
ADJ (Pin 2): Adjust. For the adjustable LT3010, this is the
input to the error amplifier. This pin is internally clamped
to ±7V. It has a bias current of 50nA which flows into the
pin (see curve of ADJ Pin Bias Current vs Temperature
8
V
IN
Figure 1. Kelvin Sense Connection
+
8
5
IN
SHDN
LT3010
GND
SENSE
4, 9
OUT
1
2
R
P
+
30105 F01
LOAD
P
) of
in the Typical Performance Characteristics). The ADJ pin
voltage is 1.275V referenced to ground, and the output
voltage range is 1.275V to 60V.
NC (Pins 3, 6, 7): No Connection. May be floated, tied to
IN or tied to GND.
GND (Pin 4, Pin 9): Ground. The exposed backside (pin 9)
of the package is an electrical connection for GND. As
such, to ensure optimum device operation, pin 9 must be
connected directly to pin 4 on the PC board.
SHDN (Pin 5): Shutdown. The SHDN pin is used to put
the LT3010 into a low power shutdown state. The output
will be off when the SHDN pin is pulled low. The SHDN
pin can be driven either by 5V logic or open-collector logic
with a pull-up resistor. The pull-up resistor is only required
to supply the pull-up current of the open-collector gate,
normally several microamperes. If unused, the SHDN pin
must be tied to a logic high or V
IN (Pin 8): Input. Power is supplied to the device through
the IN pin. A bypass capacitor is required on this pin if
the device is more than six inches away from the main
input filter capacitor. In general, the output impedance of
a battery rises with frequency, so it is advisable to include
a bypass capacitor in battery-powered circuits. A bypass
capacitor in the range of 1µF to 10µF is sufficient. The
LT3010 is designed to withstand reverse voltages on the IN
pin with respect to ground and the OUT pin. In the case of
a reversed input, which can happen if a battery is plugged
in backwards, the LT3010 will act as if there is a diode in
series with its input. There will be no reverse current flow
into the LT3010 and no reverse voltage will appear at the
load. The device will protect both itself and the load.
IN
.
30105fe