AS5145H-HSST-500 austriamicrosystems, AS5145H-HSST-500 Datasheet - Page 23
![no-image](/images/manufacturer_photos/0/0/84/austriamicrosystems_sml.jpg)
AS5145H-HSST-500
Manufacturer Part Number
AS5145H-HSST-500
Description
IC ENCODER ROTARY 16-SSOP
Manufacturer
austriamicrosystems
Type
Linear, Rotary Encoder - Programmabler
Datasheet
1.AS5145H-HSST-500.pdf
(36 pages)
Specifications of AS5145H-HSST-500
Sensing Range
45mT ~ 75mT
Voltage - Supply
3 V ~ 3.6 V, 4.5 V ~ 5.5 V
Current - Supply
21mA
Current - Output (max)
4mA
Output Type
Quadrature with Index (Incremental)
Features
Programmable
Operating Temperature
-40°C ~ 150°C
Package / Case
16-SSOP (0.200", 5.30mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
AS5145H-HSST-500TR
AS5145
Data Sheet - A p p l i c a t i o n I n f o r m a t i o n
9.2 Alignment Mode
The alignment mode simplifies centering the magnet over the center of the chip to gain maximum accuracy.
Alignment mode can be enabled with the falling edge of CSn while PDIO = logic high
a 12-bit displacement amplitude output. A high value indicates large X or Y displacement, but also higher absolute magnetic field strength. The
magnet is properly aligned, when the difference between highest and lowest value over one full turn is at a minimum.
Under normal conditions, a properly aligned magnet will result in a reading of less than 128 over a full turn.
The MagINCn and MagDECn indicators will be = 1 when the alignment mode reading is < 128. At the same time, both hardware pins MagINCn
(#1) and MagDECn (#2) will be pulled to VSS. A properly aligned magnet will therefore produce a MagINCn = MagDECn = 1 signal throughout a
full 360º turn of the magnet.
Stronger magnets or short gaps between magnet and IC may show values larger than 128. These magnets are still properly aligned as long as
the difference between highest and lowest value over one full turn is at a minimum.
The Alignment mode can be reset to normal operation by a power-on-reset (disconnect / re-connect power supply) or by a falling edge on CSn
with PDIO = low.
Figure 15. Enabling the Alignment Mode
Figure 16. Exiting Alignment Mode
9.3 3.3V / 5V Operation
The AS5145 operates either at 3.3V ±10% or at 5V ±10%. This is made possible by an internal 3.3V Low-Dropout (LDO) Voltage regulator. The
internal supply voltage is always taken from the output of the LDO, meaning that the internal blocks are always operating at 3.3V.
For 3.3V operation, the LDO must be bypassed by connecting V
For 5V operation, the 5V supply is connected to pin V
supposed to be placed close to the supply pin
Note: The V
The output voltage of the digital interface I/O’s corresponds to the voltage at pin V
www.austriamicrosystems.com/AS5145
DD
3V3 output is intended for internal use only It must not be loaded with an external load.
PDIO
CSn
CSn
PDIO
(see Figure 17)
2µs
min.
DD
5V, while V
min.
2µs
with recommended 2.2µF).
DD
AlignMode enable
3V3 with V
Revision 1.11
exit AlignMode
DD
3V3 (LDO output) must be buffered by a 1...10µF capacitor, which is
DD
5V
DD
(see Figure
(see Figure
5V, as the I/O buffers are supplied from this pin.
15). The Data bits D11-D0 of the SSI change to
17).
Read-out
Read-out
via SSI
via SSI
23 - 36