A1203EUA-T Allegro Microsystems Inc, A1203EUA-T Datasheet - Page 9
![IC SW CONTINUE TIME BIPO 3-SIP](/photos/19/2/190261/3833576_sml.gif)
A1203EUA-T
Manufacturer Part Number
A1203EUA-T
Description
IC SW CONTINUE TIME BIPO 3-SIP
Manufacturer
Allegro Microsystems Inc
Type
Bipolar Latchr
Datasheet
1.A1203LLHLT-T.pdf
(13 pages)
Specifications of A1203EUA-T
Sensing Range
95G Trip, -95G Release
Voltage - Supply
3.8 V ~ 24 V
Current - Supply
7.5mA
Current - Output (max)
25mA
Output Type
Digital, Open Drain
Features
Regulated Voltage
Operating Temperature
-40°C ~ 85°C
Package / Case
3-SIP
Operate Point Typ
26G
Termination Type
Through Hole
No. Of Pins
3
Hall Effect Type
Bipolar
Supply Voltage Min
3.8V
Release Point Min
-95G
Peak Reflow Compatible (260 C)
Yes
Output Current
20mA
Filter Terminals
Through Hole
Rohs Compliant
Yes
Leaded Process Compatible
Yes
Operate Point Max
95G
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
A1202
and A1203
the field is reduced beyond the B
back to the low state.
The typical output behavior of the A120x devices is latching.
That is, switching to the low state when the magnetic field at the
Hall element exceeds the operate point threshold, B
point, the output voltage is V
is reduced to below the release point threshold, B
output, V
are specified in the Magnetic Characteristics table, on page 3.
Note that, as shown in figure 1, these switchpoints can lie in
either north or south polarity ranges.
The A120x family is designed to attain a small hysteresis, and
thereby provide more sensitive switching. Although this means
that true latching behavior cannot be guaranteed in all cases,
proper switching can be ensured by use of both south and north
magnetic fields, as in a ring magnet. The hysteresis of the A120x
family allows clean switching of the output, even in the presence
of external mechanical vibration and electrical noise.
Figure 2. Continuous-Time Application, B < B
Position 1, power is applied to the device. Position 2, the output assumes the correct state at a time prior to the maximum Power-On Time, t
The case shown is where the correct output state is HIGH . Position 3, t
valid, a control unit reads the output. Position 5, power is removed from the device.
OUT
, goes high. The values of the magnetic parameters
OUT(SAT)
V
V
OUT
CC
OP
level, the device switches
. When the magnetic field
1
RP
.. This figure illustrates the use of a quick cycle for chopping V
RP
OP
, the device
Continuous-Time Bipolar Switch Family
. At this
2
t
PO(max)
PO(max)
3
Bipolar devices adopt an indeterminate output state when pow-
ered-on in the absence of a magnetic field or in a field that lies
within the hysteresis band of the device.
For more information on Bipolar switches, refer to Application
Note 27705, Understanding Bipolar Hall Effect Sensor ICs.
CONTINUOUS-TIME BENEFITS
Continuous-time devices, such as the A120x family, offer the
fastest available power-on settling time and frequency response.
Due to offsets generated during the IC packaging process,
continuous-time devices typically require programming after
packaging to tighten magnetic parameter distributions. In con-
trast, chopper-stabilized switches employ an offset cancellation
technique on the chip that eliminates these offsets without the
need for after-packaging programming. The tradeoff is a longer
settling time and reduced frequency response as a result of the
chopper-stabilization offset cancellation algorithm.
has elapsed. The device output is valid. Position 4, after the output is
Output Sampled
4
5
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
CC
in order to conserve battery power.
t
t
PO(max)
.
9