ERT-D3FGL131S Panasonic - ECG, ERT-D3FGL131S Datasheet - Page 5

• Manufacturer Part Number: ERT-D3FGL131S
• Description: 130 OHM THERMISTOR
• Manufacturer: Panasonic - ECG
• Series: ERT-Dr

Specifications of ERT-D3FGL131S

• Resistance In Ohms @ 25°c: 130
• Resistance Tolerance: ±15%
• B25/50: 3700K
• Operating Temperature: -30°C ~ 60°C
• Power - Max: 600mW
• Lead Length: 1.18" (30.00mm)
• Mounting Type: PCB, Through Hole
• Package / Case: Molded Disc
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• B Value Tolerance: -
• B0/50: -
• B25/75: -
• B25/85: -
• B25/100: -
• Other names: ERTD3FGL131S; PNT134

The Disc Type NTC Thermisters (hereafter referred to as ÒThe NTC ThermistorsÓ) may fail in burnout, flaming or
glowing in the worst case, when subjected to severe conditions of electrical, environmental and/or
mechanical stresses.
The following
questions regarding the ÒHandling PrecautionsÓ, please contact our engineering section or factory.
1.
2. Application Notes
Disc Type NTC Thermistors
1.2 Operating Temperature Range
2.5 Long Term Storage
1.1 Operating Power
1.3 Plastic Molding and Potting
1.4 Environmental Conditions
1.5 Mounting
1.6 Fail-Safe Design for Equipment
2.1 Soldering Flux
2.2 Post Soldering Cleaning
2.3 Abnormal Mechanical Stresses
2.4 Soldering
Safety Precautions
The NTC Thermistors should not be operated beyond their specified Maximum Permissible Power in the Catalog or
the Individual Specifications, otherwise , burnout or damages due to the thermal run awa could result. (if operated in
ambient temperature above 25 ¡C, power rating should be derated in accordance with the derating curve.)
The NTC Thermistors should not be operated beyond their specified Operating Temperature Range of in
the Catalog or the Individual Specifications.
(Do not touch the heated part of the NTC Themistors by hand during operation)
In case of plastic molding or potting, the NTC Thermistors may be damaged or deteriorated by extreme
mechanical stresses such as expanding and shrinking forces caused by the heat treatment of the plastics
applied (depending on curing conditions and types of plastics)
The NTC Thermistors should not be operated and/or stored under the following environmental conditions;
a) Direct exposure to water or drops of water.
b) Direct exposure to sunlight.
c) Under conditions of high humidity or water condensation.
d) Direct exposure to oil, gasoline or organic solvent and/or atomospheres of them.
e) Under conditions of deoxidized or corrosive atomospheres such as chlorine, hydrogen sulfide, sulfur oxide
f)
Do not let other parts touch the Thermistors because other coating is not a generated insulator.
In application of the Termistors, equipment should be protected against deterioration and failures of the Thermistors.
Rosin-based and non-activated type soldering flux is recommended.
In case of solvent cleaning, outer coating material of the NTC Thermistors may acquire the solvent, de-
pending on the cleaning condition and type of cleaning solvent.
The NTC Thermistors may be damaged or deteriorated, when dropped or exposed to a large impact. Excessive
shock and impact should not be applied.
(1) When soldering the thermistor, solder for as short time as possible to minimize the exposure time of
(2) In soldering the device, the body and outer coating section should not be touched by molten solder
(1) NTC Thermistors should not be stored under severe conditions of high temperature and/or high humidity.
(2) NTC Thermistors should not be stored under conditions of corrosive atomospheres such as hydrogen
(3) NTC Thermistors should not be exposed to direct sunlight.
(4) NTC Thermistors should not be stored under conditions of condensation.
(5) Store them indoors under 40 ¡C max. and 75 %RH max.
Precautions for Safety
or vinyl chloride.
Under severe conditions of extreme vibration or shock.
the element to the melting point of solder.
Take into account the solder-heat resistance of the product before use.
and/or heated iron tip.
sulfide, sulfur oxide, chlorine, and ammonia etc.
Use them within one year of manufacture and check the solderability before use.
Ò
Safety PrecautionsÓ and ÒApplication NotesÓ should be taken into consideration. For any
Handling Precautions
NTC Thermistors (Disc Type)