CJ1W-NC214 Omron, CJ1W-NC214 Datasheet - Page 528
CJ1W-NC214
Manufacturer Part Number
CJ1W-NC214
Description
High Speed Pulse Train 2 Axes
Manufacturer
Omron
Datasheet
1.CJ1W-NC214.pdf
(601 pages)
Specifications of CJ1W-NC214
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 528 of 601
- Download datasheet (14Mb)
12
12-3 LED Error Indicator
12-19
RUN ERC ERH SYNC X
−
−
LED
Y
Z
U
No Origin Input
No Origin Proximity
Input
Origin Input Mask
Position Overflow
ABS Encoder Origin
Position Offset
Overflow
ABS Encoder Origin
Position Offset
Calculation Not
Possible
Absolute Movement
Position Error
Absolute Movement
Speed Error
Error name
CJ Position Control Units OPERATION MANUAL (CJ1W-NC214/234/414/434)
The origin input was not
detected during origin search.
The origin proximity input was
not detected in an origin
search operation that uses the
origin proximity input.
The command present
position became greater than
the upper limit (overflow) or
smaller than the lower limit
(underflow) of the usable
range due to the movement by
the origin input mask amount,
when the ORIGIN SEARCH
OPERATION mode was
"Proximity Rev Turn/Origin
Input Mask Amount".
When you use an absolute
encoder, the absolute encoder
origin position offset which
was calculated upon
completion of Origin Search
exceeded the setting range.
When you use an absolute
encoder, the feedback present
position became greater than
the upper limit (overflow) or
smaller than the lower limit
(underflow) of the usable
range during origin search.
The command position of
absolute movement is outside
the specified range.
The command speed of
absolute movement is outside
the specified range.
Cause
Check the connection and
setting of the origin input, and
then execute an error reset.
If this error occurs (upon limit
input), the PCU stops the
applicable axis according to
the setting of the
corresponding axis
parameter.
Check the connection and
setting of the origin proximity
input, and then execute an
error reset.
If this error occurs (upon limit
input), the PCU stops the
applicable axis according to
the setting of the
corresponding axis
parameter.
Check the setting of the origin
input mask amount and range
of the command present
positions used, and then
execute an error reset.
If this error occurs, the PCU
decelerates the applicable
axis to a stop.
Set up the absolute encoder
again, and then execute an
error reset.
Check the unit setting for
feedback pulse input and
range of feedback present
positions which you use, and
then execute an error reset.
If this error occurs, the PCU
decelerates the applicable
axis to a stop.
Check the set value of the
command position and then
execute an error reset.
If this error occurs, the PCU
decelerates the applicable
axis to a stop.
Check the set value of the
command speed and then
execute an error reset.
If this error occurs, the PCU
decelerates the applicable
axis to a stop.
Remedy
Related parts for CJ1W-NC214
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
ANALOG IN, CJ1, 4CH, HIGH SPPE
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
High Speed Pulse Train 2 Axes
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
High Speed Pulse Train 4 Axes
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
High Speed Pulse Train 4 Axes
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
CJ Profinet Master
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Ethernet I/P Module
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
HIGH SPEED COUNTER 500Khz 2 CH
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Isolated Universal Analog 4pt
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
CJ1 CompoNet Master
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: