CJ1W-NC234 Omron, CJ1W-NC234 Datasheet - Page 262
CJ1W-NC234
Manufacturer Part Number
CJ1W-NC234
Description
High Speed Pulse Train 2 Axes
Manufacturer
Omron
Datasheet
1.CJ1W-NC214.pdf
(601 pages)
Specifications of CJ1W-NC234
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 262 of 601
- Download datasheet (14Mb)
5
5-7 Memory Operation Condition Data
5-101
Edge Selection
Data 1 Area Selection
Data 1 Word
Data 1 Bit
Data 2 Area Selection
Data 2 Word
Data 2 Bit
Edge judgment and level judgment are available as the methods to evaluate true/false of a
conditional expression for other than a timer (time designation) or counter (count designation).
Under level judgment, judge true/false when you judge condition data.
Under edge judgment, the program waits until the condition changes "from True to False to
True," if the condition is already True before the judgment of condition data.
For example, assume a sequence for which you specify positioning and set a skipping condition.
If the condition is True before you execute the sequence, positioning is not performed and the
sequence skips under level judgment.
Under edge judgment, execute positioning, and if the condition changes "from True to False to
True," the sequence skips at that point.
Note, however, that condition data for JUMP instructions always conforms to the operation
based on level judgment.
Specify the area on the left-hand side of the conditional expression for comparison.
For the constant, you can only set either data 1 or data 2 in the case of data comparison.
Specify the word address of data 1 (left-hand side) for comparison condition. Specify the
number of offset words.
For the specification method, specify the word address as an offset in words from the
beginning word, relative to the target area which you specified by data 1 area selection.
Specify the bit position of the word of data 1 (left-hand side). This setting is enabled only for bit
comparison.
Specify the area on the right-hand of the conditional expression for comparison.
For the constant, you can only set either data 1 or data 2 in the case of data comparison.
Specify the word address of data 2 (right-hand side) for comparison condition. Specify the
number of offset words.
For the specification method, specify the word address as an offset in words from the beginning
word, relative to the target area which you specified by data 2 area selection.
Specify the bit position of the word of data 2 (right-hand side). This setting is enabled only for
bit comparison.
CJ Position Control Units OPERATION MANUAL (CJ1W-NC214/234/414/434)
Related parts for CJ1W-NC234
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
ANALOG IN, CJ1, 4CH, HIGH SPPE
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
High Speed Pulse Train 2 Axes
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
High Speed Pulse Train 4 Axes
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
High Speed Pulse Train 4 Axes
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
CJ Profinet Master
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Ethernet I/P Module
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
HIGH SPEED COUNTER 500Khz 2 CH
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Isolated Universal Analog 4pt
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
CJ1 CompoNet Master
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: