ETM1411-2307 CAL CONTROLS, ETM1411-2307 Datasheet - Page 2

• Manufacturer Part Number: ETM1411-2307
• Description: DIGITAL TIMER, 1 X RELAY, 230VAC
• Manufacturer: CAL CONTROLS

Specifications of ETM1411-2307

• Supply Voltage Range: 184VAC To 253VAC
• Operating Time Range: Selectable 0.01 To 99.59 Min Or Hour
• Power Consumption: 3VA
• External Depth: 70mm
• External Length / Height: 34mm
• External Width: 77mm
• Ip/nema Rating: IP60 Front Panel / IP20 Rear Panel
• Rohs Compliant: Yes
• Digit Height: 12mm
• Input Voltage Max: 230VAC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

INDICATOR OF
CONTACT OUTPUT
30 59
1000
If
programming mode is entered.
key is pressed and held for 3 seconds,
ETM1411
CAL
OUT
T.lol
T.uPl
In.de
When pressed
with the step defined by In.de .
Time
value
INDICATOR OF
SELECTING
HOUR
T.S.
DIGITAL TIMER
HOUR
MIN
The lower limit
of the setpoint.
Adjustable between
0.01 and
The upper limit
of the setpoint.
Adjustable between
T.lol
Increase or decrease
step of the setpoint.
Adjustable between
1 and 30.
INDICATOR OF
SELECTING
MINUTE
SET
and 99.59.
key, TIMER set value flashes and by using
T.uPl.
60 00
START
STOP
Programming Mode
Run Mode
Displayed time value in the run mode, parameter value or name in the programming mode.
When held down for one second in the run mode, timer runs. Used for selecting menu and increasing setpoint value of the parameters in the programming mode and for increasing the setpoint value in the
run mode. When held down for a few seconds, the change rate accelerates.
Used for adjusting the value of the setpoint in the run mode and for adjusting the selected parameter in the programming mode. For adjusting the selected parameter, while holding
adjusted by using
When held down for one second in the run mode, timer and voiced warning are stopped.(When
for selecting parameters and decreasing the setpoint value in the programming mode and for decreasing the setpoint value in the run mode. When held down for a few seconds, the change rate accelerates.
Out.t.
Sond.
T.bas
Str.t.
T.c.
59 59
Selection of buzzer voice type.
Adjustable 16 different voice types.
If this parameter is selected 0,
voiced warning is canceled.
Selection of time unit.
If
adjutable max. 99:59 min.
If
adjutable max. 99:59 h.
Selection of start type.
By external start input and
start/stop keys, timer can be run
and stopped. 4 different selection
types are defined in the
control diagram.
Selection of relay output.
If
by start and relay contact shuts.
When time is over, relay contact
opens. If
runs by start.
relay contact shuts.
min
Hour
typ.0
and
is selected, time can be
is selected
typ.1
is selected, timer runs
When time is over,
keys.
is selected, timer
and
, time can be
60 00
keys the value can be adjusted
A.-t.S.
S.Cod.
A.-
SE
T.c
.
Access code for
timer configuration menu.
NonE
P.yes
P.no
Access code for timer set menu
NonE
P.yes
P.no
Access code for entering
security menu.
This parameter should be 411.
= Parameters of menu
= Parameters of menu
= Menu is invisible.
= Menu is invisible.
= Parameters of menu
are only visible.
= Parameters of menu
are only visible.
If
run mode is entered.
are changeable.
2/2
are changeable.
key is pressed,
Str.t.
=
TYP.1
Str.t.
Str.t.
TYP.2
TYP.1
TYP.3
TYP.0
TYP.0
Out.t.
Out.t.
mode is selected, timer and voiced warning can be stopped if external start input is off). Used
CONTROL DIAGRAM BY START & STOP KEYS
CONTROL DIAGRAM BY EXTERNAL START INPUT
Indicator
Indicator
Indicator
Indicator
Power
Power
Power
Stop
key
Power
Start
key
Stop
key
Start
key
Stop
key
Start
input
Start
input
Out
Out
Out
Out
TYP.0
TYP.0
TYP.1
TYP.1
key, the value can be
ETM1411-E-03