EA-IF-E2 EA ELEKTRO-AUTOMATIK, EA-IF-E2 Datasheet - Page 68

• Manufacturer Part Number: EA-IF-E2
• Description: INTERFACE ETHERNET (EA-PSI/BCI800R)
• Manufacturer: EA ELEKTRO-AUTOMATIK

Specifications of EA-IF-E2

• Svhc: No SVHC (18-Jun-2010)
• Accessory Type: Interface Card
• Applications: Engineering Laboratory And Complex Industrial Application
• Approval Bodies: CE / EN
• Rohs Compliant: Yes
• For Use With: EA Elektro-Automatik PSU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

About the interface cards
© 009, Elektro-Automatik GmbH & Co. KG
System commands
[SYSTem:]
Note: the device can only be monitored, if not in remote mode. This means, you can only query actual values and
status. In order to set status, modes and set values, you need to switch the device to remote mode with
STATE 1
blocks and modes can be found in the user manual of your device. The lock state can be queried by this command:
[SYSTem:]
Examples:
SYST:LOCK:OWN?
SYST:LOCK:STAT1
SYST:LOCKON
Attention! The following two commands are only supported by the network card IF-E1!
[SYSTem:]
Example:
SYST:DATA:SET2,1,50,100,0
[SYSTem:]
Example:
SYST:DATA:REQ2,1,50
ERRor:ALL?
ERRor:NEXT?
LOCK
LOCK
VERSion?
DATA
DATA
[:STATE]
:OWNer?
:SET
:REQuest
or
*RST
(see 2.2).
-><Err>[,<Err>]… Queries the error queue, used to read out error descriptions and codes;
-><Err>
<B0>
-><B1>
-><SRD>
<CHAR>
<CHAR>
In order to do so, the remote mode must not be blocked. More information about conditions,
Queries the lock state to determine if remote mode is allowed
Puts the device in remote control mode (setting of values allowed now)
Ditto
Send the hexadecimal telegram 0x0 01 3 64 00 to the device.
If device is in remote control, it will set the output voltage to 100%.
Corresponds to the SCPI command SOUR:VOLTMAX
Send the hexadecimal telegram 0x0 01 3 to the device.
This request the voltage set value.
Corresponds to the SCPI command SOUR:VOLT?
The response will be two values, for example 100,0. They corrrespond to the
hexadecimal value 0x6400 and means 100% set value.
the bits err, esr and ESR:Condition are cleared
Queries only the last error from the queue; if the queue is empty, bits
err, esr and ESR:Condition are cleared
1= puts the device into remote control mode, if SYST:LOCK:OWN? would
0= exits remote control mode, returns to normal device operation
Get the current lock state
NONE:
LOCal:
REMote: the device is in remote mode via IF-G1
(Bit 8=0,9=1,10=0 in OPER Register)
Query SCPI-Version
Transport encapsulated telegram in binary format
Here: Send data (SET) (also see sections 7.10 and 9.)
Bytes can be given as hexadecimals, e.g. #H3 for 0x3, or decimals
Transport encapsulated telegram in binary format
Here: Request data (also see sections 7.10 and 9.)
(Bits 8,9,10 =0 in OPER:Condition)
(Bits 8=1,9=0,10=0 in OPER:Condition )
External mode is interpreted as LOCal.
(Bit 8=0,9=0,10=1 in OPER:Condition)
beanswered with „NONE“
if returned, the device can be put to remote mode
device is in local mode and blocked for remote mode
LOCK:
EN
68