ACPL-M61T-500 Avago Technologies US Inc., ACPL-M61T-500 Datasheet - Page 5

• Manufacturer Part Number: ACPL-M61T-500
• Description: Automotive 10MBd Coupler Tape Reel
• Manufacturer: Avago Technologies US Inc.
• Series: R²Coupler™r

Specifications of ACPL-M61T-500

• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 50mA
• Data Rate: 10MBd
• Propagation Delay High - Low @ If: 46ns @ 6.5mA
• Current - Dc Forward (if): 20mA
• Input Type: DC
• Output Type: Open Collector
• Mounting Type: Surface Mount
• Package / Case: 6-SOIC (0.173", 4.40mm Width) 5 Leads
• Number Of Elements: 1
• Forward Voltage: 1.85V
• Forward Current: 20mA
• Output Current: 50mA
• Isolation Voltage: 3750Vrms
• Package Type: SOIC
• Operating Temp Range: -40C to 125C
• Power Dissipation: 85mW
• Propagation Delay Time: 75ns
• Pin Count: 5
• Mounting: Surface Mount
• Reverse Breakdown Voltage: 5V
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Package Characteristics
*
Switching Specifications (AC)
Over recommended temperature T
*All Typicals at T
Notes:
1. Bypassing of the power supply line is required with a 0.1 μF ceramic disc capacitor adjacent to each optocoupler. The total lead length between
2. Peaking circuits may produce transient input currents up to 40 mA, 50 ns maximum pulse width, provided average current does not exceed 20
3. Device considered a two terminal device: pins 1 and 3 shorted together and pins 4, 5 and 6 shorted together.
4. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4800 V
5. The t
6. The t
7. CM
8. CM
9. For sinusoidal voltages, (|dV
10. See application section; “Propagation Delay, Pulse-Width Distortion and Propagation Delay Skew” for more information.
11. t
12. Input current derates linearly above 85°C free-air temperature at a rate of 0.25 mA/°C.
13. Input power derates linearly above 85°C free-air temperature at a rate of 0.375mW/°C.
14. Output power derates linearly above 85°C free-air temperature at a rate of 0.475 mW/°C.
5
Parameter
Input-Output Momentary Withstand
Voltage*
Input-Output Resistance
Input-Output Capacitance
Parameter
Propagation Delay Time
to Low Output Level
Propagation Delay Time
Propagation Delay Skew
Pulse Width Distortion
Output Rise Time (10% -
90%)
Output Fall Time (10% - 90%)
Common Mode Transient
Immunity at High Output
Level
Common Mode Transient
Immunity at Low Output
Level
to High Output Level
The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your
equipment level safety specification, or Avago Technologies Application Note 1074, “Optocoupler Input-Output Endurance Voltage. ”
both ends of the capacitor and the isolator pins should not exceed 10 mm.
mA.
output pulse.
output pulse.
operating condition range.
PSK
H
L
is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state (i.e., V
is equal to the worst case difference in t
is the maximum tolerable rate of rise of the common mode voltage to assure that the output will remain in a high logic state (i.e., V
PLH
PHL
propagation delay is measured from 3.25 mA point on the falling edge of the input pulse to the 1.5 V point on the rising edge of the
propagation delay is measured from 3.25 mA point on the rising edge of the input pulse to the 1.5 V point on the falling edge of the
A
= 25°C, Vcc = 5V.
CM
|/dt)max = Sf
Symbol
t
t
t
| t
t
t
|CM
|CM
PHL
PLH
PSK
rise
fall
PHL
H
L
|
|
- t
A
PLH
= -40°C to 125°C, V
CM
Symbol
V
R
C
|
V
PHL
ISO
I-O
I-O
CM
Min.
15
15
and/or t
(p-p).
Min.
4000
Typ.
46
50
3.5
24
10
30
30
PLH
that will be seen between units at any given temperature within the worst case
CC
Typ.
10
0.6
Max.
75
100
75
100
40
35
= 5.0 V, I
14
Max.
Units
ns
ns
ns
ns
ns
ns
ns
ns
kV/μs
kV/μs
F
= 6.5mA unless Otherwise Specified.
Units
V
Ω
pF
Test Conditions
T
T
V
V
rms
A
A
CM
CM
=25°C
=25°C
=1000Vp-p
=1000Vp-p
Test Conditions
RH ≤ 50%, t = 1 min;T
25°C
V
f = 1 MHz; V
I-O
= 500 Vdc
R
C
I
Vo(min) = 2V
I
T
R
Vo(max) = 0.8V
I
T
R
F
F
F
A
A
L
L
L
L
= 6.5mA
= 0mA
= 6.5mA
RMS
=25°C
=350Ω
=25°C
=350Ω
I-O
= 350Ω
= 15pF
= 0 Vdc
for 1 second.
A
=
Fig.
6, 7, 8
6, 7, 8
14, 15
9
10
10
11
Fig.
OUT
OUT
< 0.8 V).
> 2.0 V).
Note
Note
6
5
10,
11
10
7,9
8,9