A95UF SHURE, A95UF Datasheet

A95UF

Manufacturer Part Number

A95UF

Description

TOOLS,SCREWDRIVERS,TORX,TRANSFORMER

Manufacturer

SHURE

Datasheet

1.A95UF.pdf (4 pages)

Specifications of A95UF

Low Z, Female Xlr To High Z Mc1m Connector With Mating 1/4? Phone,audio Equipment,communications Microphones ,shure

ROHS COMPLIANT

Primary Impedance

300ohm

Secondary Impedance

41kohm

Rohs Compliant

Current page: 1 of 4
Download datasheet (152Kb)

MODEL A95UF LINE MATCHING TRANSFORMER

The Shure Model A95UF is a reversible line matching transformer that can match

low impedance microphones to high impedance inputs, or match high impedance

microphones to low impedance inputs. The A95UF lets you use long runs of cable

with either low impedance or high impedance microphones. However, when con-

necting the high impedance end of the A95UF to a high impedance microphone,

the cable should be no more than 4.6 m (15 ft.) long. The A95UF prevents high fre-

quency attenuation, level loss, and pickup of noise or hum.

The A95UF can be configured for two low impedance settings: 19Ω to 75Ω, or 75Ω

to 300Ω. As supplied, the low impedance end is configured for 75Ω to 300Ω.

The A95UF is furnished with a female XLR connector at the low impedance end,

and a standard 1/4-inch phone plug and a phone jack adapter at the high

impedance end.

LOW IMPEDANCE SELECTION

As supplied, the low impedance end of the A95UF is configured for use with inputs

rated at 75Ω to 300Ω. To reconfigure the low impedance end for inputs rated at

19Ω to 75Ω, refer to the figure below and proceed as follows:

27D1926 (Rev. 3)

Remove the low-impedance plug element by turning the screw counter-

clockwise and withdrawing the element from the case.

Unsolder the YELLOW lead from pin 3 and insulate the bare wire at the

end of the lead with the insulator from the ORANGE lead.

Solder the ORANGE lead to pin 3.

Rotate the plug element three turns to twist the leads, and replace the

element in the housing. Reinstall the screw by turning it clockwise.

Model A95UF

User Guide

Printed in U.S.A.

Related parts for A95UF

A95UF Summary of contents

Page 1

... However, when con- necting the high impedance end of the A95UF to a high impedance microphone, the cable should be no more than 4.6 m (15 ft.) long. The A95UF prevents high fre- quency attenuation, level loss, and pickup of noise or hum. ...

Page 2

BLACK 1 2 GREEN 3 ORANGE YELLOW SPECIFICATIONS Frequency Response kHz. Response more than 3 dB down from flat. Impedance Green/Orange winding: Low Z (19 to 75Ω) Green/Yellow winding: Low Z (75 ...

Page 3

... Shure Incorporated, Attention: Service Department, at the address below. Outside of the United States, return the product to your dealer or Authorized Service Center. Addresses are listed on www.Shure.com or can be obtained by contacting Shure at the address listed below. A95UF Winding Green/Orange (19Ω to 75Ω) Green/Yellow (75Ω to 300Ω) Black/Red Black/Red ...

Page 4

... This warranty is not transferable. This warranty does not apply in cases of abuse or misuse of the product, use contrary to Shure’s instruction, ordinary wear and tear, an act of God, negligent use, purchase from a party other than Shure or a Shure-authorized reseller, unauthorized repair, or modification of the product. ...

Related keywords

A95UF datasheet
A95UF data sheet
A95UF pdf datasheet
A95UF component
A95UF part
A95UF distributor
A95UF RoHS
A95UF datasheet download