6D308 4D SYSTEMS, 6D308 Datasheet

6D308

Manufacturer Part Number

6D308

Description

BRIDGE, USB-RS232, UUSB-MB5

Manufacturer

4D SYSTEMS

Type

USB To Serial UART Bridge Convr

Datasheet

1.6D308.pdf (1 pages)

Specifications of 6D308

Mcu Supported Families

GOLDELOX-GFX, PICASO-GFX

Tool / Board Applications

Prototype Hardware Tool Used For Programming PMMC Firmware Files And 4DGL User Code

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Current page: 1 of 1
Download datasheet (157Kb)

Product Overview:

The microUSB (µUSB-MB5) is a USB to RS-232 bridge converter which is simple,

cost effective, very small and easy to use. It uses a mini-B type USB connector to

connect to your PC and is based on the CP2102 Bridge from Silicon Labs. It

provides the user with multi baud rate serial data and access to flow control signals

in a convenient 10 pin 0.1” pitch Dual-In-Line package. The µUSB-MB5 is ideal for

prototype or production.

Main Features:

USB 2.0 compliant Full Speed 12Mbps maximum speed; Suspend supported

Hardware or Xon/Xoff handshaking supported; 300bps to 1Mbps

UART supports 5-8 bit data, 1-2 Stop bits, odd/even and no parity

Integrated EEPROM for Vendor ID, product ID, serial number, release number

On-chip 3.3V regulator available; power on reset circuit

Virtual COM port drivers allow operation with existing COM port PC applications

Supports Windows, MAC (OSX-9 and above) and Linux (2.4 kernel and above)

Self powered or USB powered; -40 to +85 deg C temp range

Small size; 15.4mm x 17.7mm (0.5” x 0.5”) approx.

Traffic/Operation LED indicates board status

4D Systems Pty. Ltd.

Typical Applications:

The microUSB (µUSB-MB5) makes an easy USB-Serial interface, so you can

easily create USB to RS-232 converters , USB to RS-422/RS-485 converters ,

upgrade legacy RS232 devices, make PDA and cellphone USB interface

cables, barcode readers, POS terminals, etc.

In any application, make sure the TX and RX lines from the µUSB are

crossed over to the attached peripheral. That is, the TX from the µUSB

connects to the RX of the target and the RX from the µUSB connects to the

TX of the target device.

Note: the TX and RX signal levels are between 0.0 Volts and 3.3 Volts.

For Help and Other Information:

product web-page of your distributor.

figure 2: typical interface with a microcontroller

www.silabs.com

Assistance with latest driver downloads go

Questions and technical support please

support@4dsystems.com.au

SUSPEND

figure 1: uUSB-MB5 Pin-Out Diagram

Name

DTR

GND

3.3V

RTS

CTS

Description

Data Terminal Ready output (active low)

Serial Data output (uUSB Transmit)

Serial Data input (uUSB Receive)

Ready to Send output (active low)

Clear To Send input (active low)

Ground

USB Suspend State (active high)

Ground

5V Power from USB (upto 500mA)

3.3V Power regulated (upto 100mA)

or visit the µUSB-MB5

support@4dsystems.com.au

figure 3: Interface to any

4D serial device such as the

uLCD-OLED and uVGA

modules with the extra 5pin

header provided.

www.4dsystems.com.au

Related parts for 6D308

Related keywords

6D308 datasheet
6D308 data sheet
6D308 pdf datasheet
6D308 component
6D308 part
6D308 distributor
6D308 RoHS
6D308 datasheet download