AME9001AETH AME, AME9001AETH Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/0/45/ame_sml.jpg)
AME9001AETH
Manufacturer Part Number
AME9001AETH
Description
CCFL Inverters & Accessories Backlight Controller
Manufacturer
AME
Specifications of AME9001AETH
Function
Backlight Controller
Input Voltage
24 V
Output Voltage
5.35 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AME9001
n Application Notes
Overview
a CCFL (cold cathode fluorescent lamp) with a high volt-
age sine wave in order to produce an efficient and cost
effective light source. The most common application for
this will be as the backlight of either a notebook com-
puter display, flat panel display, or personal digital assis-
tant (PDA).
ally glass rods about a foot long and 0.125”-0.25” in
diameter. Typically they require a sine wave of 600V and
they run at a current of several milliamperes. However,
the starting (or striking) voltage can be as high as 2000V.
At start up the tube looks like an open circuit, after the
plasma has been created the impedance drops and cur-
rent starts to flow. The IV characteristic of these tubes is
highly non-linear.
tion has been developed using some sort of transformer-
LC tank circuit combination driven by several small power
mosfets. The AME9001 application uses one external
PMOS, 2 external NMOS and a high turns ratio trans-
former with a centertapped primary. Lamp dimming is
achieved by turning the lamp on and off at a rate faster
than the human eye can detect. These "on-off" cycles
are known as dimming cycles.
Steady State Circuit Operation
tap primary of T1. The gate drive of Q2 is a pulse width
modulated (PWM) signal that controls the current into
the transformer primary and by extension, controls the
current in the CCFL. The gate drive signal of Q2 drives
all the way up to the battery voltage and down to 7.5
volts below Vbatt so that logic level transistors may be
used without their gates being damaged. An internal
clamp prevents the Q2 gate drive (OUTA) from driving
lower than Vbatt-7.5V.
the outside nodes of the transformer primary to VSS.
These transistors are driven by a 50% duty cycle square
wave at one-half the frequency of the drive signal applied
to the gate of Q2.
the CCFL application. Figure 4 and 5 are detailed views
of the power section from Figures 1 and 2. Figure 5 has
the transformer parasitic elements added while Figure 4
8
The goal of the AME9001 application circuit is to drive
The CCFL tubes used in these applications are usu-
Traditionally the high voltage required for CCFL opera-
Figure 1 (and 2) shows PMOS Q2 driving the center
NMOS transistors Q3-1 and Q3-2 alternately connect
Figure 3 illustrates some ideal gate drive waveforms for
AME, Inc.
tors Q3-1 and Q3-2 are driven out of phase with a 50%
duty cycle signal as indicated by waveforms in Figure 3.
The frequency of the NMOS drive signals will be the fre-
quency at which the CCFL is driven. PMOS transistor,
Q2, is driven with a pulse width modulated signal (PWM)
at twice the frequency of the NMOS drive signals. In
other words, the PMOS transistor is turned on and off
once for every time each NMOS transistor is on. In this
case, when NMOS transistor Q3-1 and PMOS transistor
Q2 are both on then NMOS transistor Q3-2 is off, the
side of the primary coil connected to NMOS transistor
Q3-1 is driven to ground and the centertap of the trans-
former primary is driven to the battery voltage. The other
side of the primary coil connected to NMOS transistor
Q3-2 (now “off”) is driven to twice the battery voltage
(because each winding of the primary has an equal num-
ber of turns).
to Q3-1 (the “on” transistor), transferring power to the
secondary coil of transformer. The energy transferred
from the primary excites the tank circuit formed by the
transformer leakage inductance and parasitic capaci-
tances that exist at the transformer secondary. The para-
sitic capacitances come from the capacitance of the trans-
former secondary itself, wiring capacitances, as well as
the parasitic capacitance of the CCFL. Some applica-
tions may actually add a small amount of parallel ca-
pacitance (~10pF) on the output of the transformer in
order to dominate the parasitic capacitive elements.
transformer centertap returns to ground as does the drain
of NMOS transistor Q3-2 (the drain of Q3-2 was at twice
the battery voltage). Halfway through one cycle, NMOS
transistor Q3-1 (that was on) turns off and NMOS tran-
sistor Q3-2 (that was off) turns on. At this point, PMOS
transistor Q2 turns on again, allowing current to ramp up
in the side of the primary that previously had no current.
Energy in the primary winding is transferred to the sec-
ondary winding and stored again in the leakage induc-
tance L
current alternately goes through one primary winding then
the other.
amount of power transferred from the primary winding to
the secondary winding in the transformer. Note that the
CCFL circuit can work with PMOS transistor Q2 on con-
stantly (i.e. a duty cycle of 100%), although the power
would be unregulated in this case.
does not. Referring to Figures 4 and 5, NMOS transis-
Current ramps up in the side of the primary connected
When the PMOS, Q2, is turned off, the voltage of the
The duty cycle of PMOS transistor Q2 controls the
leak
, but this time with the opposite polarity. The
CCFL Backlight Controller