SN3C1-124 AVX Corporation, SN3C1-124 Datasheet - Page 29

• Manufacturer Part Number: SN3C1-124
• Manufacturer: AVX Corporation

Specifications of SN3C1-124

• Mounting Style: Through Hole
• Operating Temp Range: -55C to 125C
• Voltage Rating Max: 50VAC/50VDC
• Lead Free Status / RoHS Status: Not Compliant

Bolt Style EMI Filters
SN Series – 12-32 Thread - Hermetically Sealed –
Circuits Available – C, L,
SPECIFICATIONS
1. Plating: Silver standard – Electro-tin or gold
2. Material:
3. Operating Temperature Range:
4. Electrical Characteristics:
5. Seal: In accordance with MIL-F-28861.
6. Marking: Standard (AVX symbol, AVX part
7. Installation: Filter is supplied with mounting nut
number)
and lockwasher. The recommended mounting
torque is 64 oz-in. ± 4 oz-in. Refer to the
“Installation and Handling” section for additional
information.
Case: Cold rolled steel standard, brass available
Leads: Copper nailhead standard. Only available
-55°C to +125°C
A. Capacitance: Guaranteed Minimum Value
B. Insulation Resistance:
C. Dielectric Withstanding Voltage (DWV):
D. DC Resistance (DCR): .01 ohm, maximum
E. Voltage Drop: 0.1 volt, maximum
F. Dissipation Factor (DF): 3% maximum
G. Rated Current: 10 Amps, maximum
Leakage rate for Class S designs shall not
exceed 1 x 10
(GMV) as listed
At 25°C: 1,000 megohm-microfarad
At 125°C: 100 megohm-microfarad
R-level designs:
Class B, Class S designs:
2.0 times rated voltage
2.5 times rated voltage
in .032" diameter. Beryllium copper lead
available. Straight lead available.
available
min., or 100,000 megohms
min., whichever is less
min., or 10,000 megohms
min., whichever is less
-7
atm cc/sec.
APPLICATIONS
The SN series offers effective filtering
from 1 MHz to 10 GHz. Glass sealed on
both ends for hermeticity, this series is
impervious to high moisture, solvents, or
other severe environmental conditions
commonly encountered in military applica-
tions. It is designed for bulkhead mounting
with nut and lockwasher supplied.
The feedthru designs yield constant filter-
ing as current level is increased from
CHARACTERISTICS
• The hermetic bolt-style design was
developed to meet or exceed the
applicable portions of MIL-F-28861/10.
The filter is assembled with a glass her-
metic seal on both ends. The rugged
monolithic capacitor element is a low
inductance design that yields superior
π
millimeters (inches)
(See Note 1)
0.05 (.002)
0.13 (.005)
0.18 (.007)
0.25 (.010)
0.51 (.020)
0.58 (.023)
0.79 (.031)
0.81 (.032)
1.02 (.040)
1.14 (.045) 23.39 (.921)
1.60 (.063)
±.010
.250
SN1
C
1.85 (.073)
3.99 (.157)
5.49 (.216)
6.12 (.241)
6.35 (.250)
7.90 (.311)
8.71 (.343)
9.45 (.372)
9.73 (.383)
—
—
STANDARD CONFIGURATION
Notes:
1. Metric equivalent dimensions
CIRCUIT DIAGRAMS
given for information only.
±.020
.343
MAX.
.220
no-load to full rated load. They are most
effective when placed in high impedance
circuits. The
sharper roll-off in filter characteristic and
perform effectively when used in medium
to low impedance circuits.
Alternate lead configurations or special
capacitance values and voltage ratings
may be ordered.
• Certain feedthru designs are rated for
SN2
L
bypass performance. The
design contains two capacitor elements
together with a ferrite bead inductor.
115 VAC/400 Hz applications. The 200
VDC
applications only.
2
±.005
±.005
.250
.311
MAX.
.040
π
±.020
.921
-section design is rated for DC
π
.216-32 UNEF-2A
(12-32)
-section designs exhibit
SN3
Pi
.032 ±.002
π
-section
27