TWR-SER2 Freescale Semiconductor, TWR-SER2 Datasheet
TWR-SER2
Specifications of TWR-SER2
Related parts for TWR-SER2
TWR-SER2 Summary of contents
Page 1
... Quick Start Guide for TWR-SER2 TWR-SER2 Enhanced serial module TOWER SYSTEM ...
Page 2
... RS232 UART2 Header TWR-SER2 Freescale Tower System The TWR-SER2 module is part of the Freescale Tower System, a modular development platform that enables rapid prototyping and tool re-use through reconfigurable hardware. Take your design to the next level and begin constructing your Tower System today. ...
Page 3
... Quick Start Guide for TWR-SER2 TWR-SER2 features • Industrial Ethernet PHY configurable as: 10/100 dual-or single-port RMII 10/100 single-port MII • Industrial High-Speed, Dual-Role USB (Host/Device) over UPLI • Dedicated host mode USB port • Four concurrent RS232 serial transceivers, including one S08JS16 based Serial-to-USB • RS485 transceiver • CAN transceiver TOWER SYSTEM ...
Page 4
TOWER SYSTEM How to build your Tower Locate the STEP 1 Elevator Modules Each elevator module is identifiable by its four card edge connectors Identify the STEP 2 Elevator Modules Each elevator module is either Primary or Secondary. They are identifiable as follows: • Primary Elevator: Written ...
Page 5
... Quick Start Guide for TWR-SER2 Make Additional STEP 7 Connections Plug in necessary cables and power sources NOTE: First-generation modules If using the first generation of TWR-ELEV modules, the board labeled Functional Elevator is equivalent to the Primary Elevator as described in the instructions above. The board labeled Dummy Elevator is different than the Secondary Elevator, but will work with most assembled Tower Systems. ...
Page 6
... TOWER SYSTEM Configuration instructions In this Quick Start Guide, you will learn how to configure the various settings on the TWR-SER2 module for use in the Tower System. Ethernet Settings Refer to these settings for typical Ethernet setting. For specific setting details refer to the TWR-SER2 Jumper Options section. • 10/100 Dual RMII J8 and J9 should be un-shunted ...
Page 7
... J23 pins 5-6, 7-8 should be shunted if using RTS/CTS flow control on UART3 (J20) CAN Settings Refer to these settings to enable the connection to the CAN Transceiver. The TWR-SER2 will be connected to a CAN device using J3. Refer to the TWR-SER2 User Manual for header pinout details. • J4 pins 3-4, 5-6 should be connected • J4 pins 1-2 can be connected to enable control of “Silent Mode” ...
Page 8
... TOWER SYSTEM TWR-SER2 Jumper Options The following is a list of all jumper options. The *default* installed jumper settings are shown in bold with asterisks. Option Ethernet Strapping Functions / Settings Ethernet Strapping Functions / Settings Setting *On* Enables RMII mode for Ethernet PHY A Dip 1 Off Enables MII mode for Ethernet PHY A ...
Page 9
... Quick Start Guide for TWR-SER2 Option Ethernet Strapping Functions/Settings RS232/485 RX Select (UART 1) RS232/485 TX Select (UART 1) CAN Isolation JS16 RS232 Isolation (UART 0) Power Down Port B Setting On Connects onboard 25 MHz clock to Ethernet PHY Clock Dip 4 *Off* Isolates onboard 25 MHz clock from Ethernet PHY Clock ...
Page 10
... TOWER SYSTEM TWR-SER2 Jumper Options continued… Option Power Down Port A RS485 Config (UART 1) RS232/485 Disable (UART 1) VBUS OC Isolation VBUS EN Isolation RS232 (UART2) Isolation RS232 (UART3) Isolation USB Device Mode Setting 1-2 Disables Ethernet PHY A 1-2 Loopback Mode (connects RE to DE) ...
Page 11
... Quick Start Guide for TWR-SER2 TOWER SYSTEM ...
Page 12
... TOWER SYSTEM TOWER SYSTEM To learn more about the TWR-SER2 and other modules within the Tower System freescale.com/twrser2. To become a member of the online Tower Geeks community towergeeks.org. Freescale, the Freescale logo and CodeWarrior are trademarks or registered trademarks of Freescale Semiconductor, Inc. Reg. U.S. Pat. & Tm. Off. All other product or service names are the property of their respective owners. ...