TDA8543T/N1 NXP Semiconductors, TDA8543T/N1 Datasheet
TDA8543T/N1
Specifications of TDA8543T/N1
Related parts for TDA8543T/N1
TDA8543T/N1 Summary of contents
Page 1
DATA SHEET TDA8543 2 W BTL audio amplifier Product specification File under Integrated Circuits, IC01 INTEGRATED CIRCUITS 1997 Jun 12 ...
Page 2
Philips Semiconductors 2 W BTL audio amplifier FEATURES Flexibility in use Few external components Low saturation voltage of output stage Gain can be fixed with external resistors Standby mode controlled by CMOS compatible levels Low standby current No switch-on/switch-off plops ...
Page 3
Philips Semiconductors 2 W BTL audio amplifier BLOCK DIAGRAM handbook, halfpage PINNING SYMBOL PIN n.c. 1 not connected n.c. 2 not connected MODE 3 operating mode select (standby, mute, operating) SVR 4 half supply voltage, decoupling ripple rejection IN+ 5 ...
Page 4
Philips Semiconductors 2 W BTL audio amplifier FUNCTIONAL DESCRIPTION The TDA8543( BTL audio power amplifier capable of delivering an output power between 1 and 2 W, depending on supply voltage, load resistance and package. Using the MODE pin ...
Page 5
Philips Semiconductors 2 W BTL audio amplifier handbook, halfpage (1) DIP16. (2) SO16. Table 7 Note 1. At THD = 10%; BTL. 1997 ...
Page 6
Philips Semiconductors 2 W BTL audio amplifier DC CHARACTERISTICS amb L SYMBOL PARAMETER V supply voltage CC I quiescent current q I standby current stb V ...
Page 7
Philips Semiconductors 2 W BTL audio amplifier Notes to the AC characteristics R2 1. Gain of the amplifier is 2 ------- - R1 2. The noise output voltage is measured at the output in a frequency range from 20 Hz ...
Page 8
Philips Semiconductors 2 W BTL audio amplifier BTL APPLICATION handbook, full pagewidth Gain = 2 ------- - R1 15 handbook, halfpage I q (mA ...
Page 9
Philips Semiconductors 2 W BTL audio amplifier 10 handbook, halfpage THD (%) 1 ( ...
Page 10
Philips Semiconductors 2 W BTL audio amplifier 2 handbook, halfpage P (W) (3) 1.6 (1) 1.2 0.8 (2) 0 0.5 1 1.5 Sine wave of 1 kHz. ( ...
Page 11
Philips Semiconductors 2 W BTL audio amplifier SE APPLICATION handbook, full pagewidth Gain = ------- - R1 10 handbook, halfpage THD (%) 1 (1) ( (3) ...
Page 12
Philips Semiconductors 2 W BTL audio amplifier 20 handbook, halfpage SVRR (dB) 40 (1) ( 100mV ...
Page 13
Philips Semiconductors 2 W BTL audio amplifier handbook, full pagewidth 1997 Jun 12 a. Top view TDA8543 100 F b. Component side. Fig.21 Printed-circuit board layout ...
Page 14
Philips Semiconductors 2 W BTL audio amplifier PACKAGE OUTLINES DIP16: plastic dual in-line package; 16 leads (300 mil); long body pin 1 index 1 DIMENSIONS (inch dimensions are derived from the original mm dimensions ...
Page 15
Philips Semiconductors 2 W BTL audio amplifier SO16: plastic small outline package; 16 leads; body width 3 pin 1 index 1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) A UNIT ...
Page 16
Philips Semiconductors 2 W BTL audio amplifier SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave ...
Page 17
Philips Semiconductors 2 W BTL audio amplifier DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification ...
Page 18
Philips Semiconductors 2 W BTL audio amplifier 1997 Jun 12 NOTES 18 Product specification TDA8543 ...
Page 19
Philips Semiconductors 2 W BTL audio amplifier 1997 Jun 12 NOTES 19 Product specification TDA8543 ...
Page 20
Philips Semiconductors – a worldwide company Argentina: see South America Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Tel. +61 2 9805 4455, Fax. +61 2 9805 4466 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. + ...