A4989SLDTR-T Allegro Microsystems Inc, A4989SLDTR-T Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/0/32/allegro_microsystems_inc_sml.jpg)
A4989SLDTR-T
Manufacturer Part Number
A4989SLDTR-T
Description
DUAL FULL BRDG MOSFET DRVR W/MICROSTEP TRANS
Manufacturer
Allegro Microsystems Inc
Datasheet
1.A4989SLDTR-T.pdf
(17 pages)
Specifications of A4989SLDTR-T
Applications
Stepper Motor Controller, 2-Phase
Number Of Outputs
1
Voltage - Load
12 V ~ 50 V
Voltage - Supply
3 V ~ 5.5 V
Operating Temperature
-20°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
38-TFSOP (0.173", 4.40mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Output
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
620-1389-2
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
A4989SLDTR-T
Manufacturer:
CDE
Quantity:
10 000
Part Number:
A4989SLDTR-T
Manufacturer:
ALLEGRO/雅丽高
Quantity:
20 000
A4989
Current Sensing
To minimize inaccuracies in sensing the I
level caused by ground-trace IR drops, the sense resistor,
RSENSEx, should have an independent return to the supply
ground star point. For low-value sense resistors, the IR drops
in the sense resistor PCB traces can be significant and should
be taken into account. The use of sockets should be avoided
as they can introduce variation in R
tact resistance.
Thermal Protection
All drivers are turned off when the junction temperature
reaches 165°C typical. This is intended only to protect the
A4989 from failures due to excessive junction temperatures.
Thermal protection will not protect the A4989 from continu-
ous short circuits. Thermal shutdown has a hysteresis of
approximately 15°C.
Circuit Layout
Because this is a switch-mode application, where rapid cur-
rent changes are present, care must be taken during layout of
the application PCB. The following points are provided as
guidance for layout. Following all guidelines will not always
be possible. However, each point should be carefully consid-
ered as part of any layout procedure.
Ground connection layout recommendations:
1. Decoupling capacitors for the supply pins VBB, VREG,
and VDD should be connected independently close to the
GND pin and not to any ground plane. The decoupling
capacitors should also be connected as close as possible to
the corresponding supply pin.
2. The oscillator timing resistor ROSC should be connected
to the GND pin. It should not be connected to any ground
plane, supply common, or the power ground.
SENSEx
PEAK
due to their con-
Application Information
current
Dual Full-Bridge MOSFET Driver
impedance trace to the supply common at a single point.
the LSS pin with reference to the GND pin using a close
grounded (tip and barrel) probe. If the voltage at LSS
exceeds the absolute maximum specified in this datasheet,
add additional clamping, capacitance, or both between the
LSS pin and the AGND pin.
may carry transient current pulses. Therefore, the traces from
GHxx, GLxx, Sxx, and LSSx should be as short as possible to
reduce the inductance of the circuit trace.
2. Provide an independent connection from each LSS pin
to the common point of each power bridge. It is not recom-
mended to connect LSS directly to the GND pin. The LSS
connection should not be used for the SENSE connection.
3. Minimize stray inductance by using short, wide copper
runs at the drain and source terminals of all power FETs.
This includes motor lead connections, the input power bus,
and the common source of the low-side power FETs. This
will minimize voltages induced by fast switching of large
load currents.
4. Consider the use of small (100 nF) ceramic decoupling
capacitors across the source and drain of the power FETs to
limit fast transient voltage spikes caused by trace inductance.
The above are only recommendations. Each application is
different and may encounter different sensitivities. Each
design should be tested at the maximum current, to ensure
any parasitic effects are eliminated.
3. The GND pin should be connected by an independent low
4. Check the peak voltage excursion of the transients on
Other layout recommendations:
1. Gate charge drive paths and gate discharge return paths
with Microstepping Translator
115 Northeast Cutoff
1.508.853.5000; www.allegromicro.com
Allegro MicroSystems, Inc.
Worcester, Massachusetts 01615-0036 U.S.A.
15