AD9268BCPZ-105 Analog Devices Inc, AD9268BCPZ-105 Datasheet - Page 33

no-image

AD9268BCPZ-105

Manufacturer Part Number
AD9268BCPZ-105
Description
Dual 16 Bit 105 High SNR ADC
Manufacturer
Analog Devices Inc
Datasheet

Specifications of AD9268BCPZ-105

Design Resources
Powering AD9268 with ADP2114 for Increased Efficiency (CN0137)
Number Of Bits
16
Sampling Rate (per Second)
105M
Data Interface
Serial, SPI™
Number Of Converters
2
Power Dissipation (max)
590mW
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LFCSP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD9268BCPZ-105
Manufacturer:
ADI/亚德诺
Quantity:
20 000
As detailed in the
Speed ADCs via SPI, the data format can be selected for offset
binary, twos complement, or gray code when using the SPI control.
Table 12. SCLK/DFS Mode Selection (External Pin Mode)
Voltage at Pin
AGND
AVDD
Digital Output Enable Function (OEB)
The AD9268 has a flexible three-state ability for the digital output
pins. The three-state mode is enabled using the OEB pin or
through the SPI. If the OEB pin is low, the output data drivers and
DCOs are enabled. If the OEB pin is high, the output data drivers
and DCOs are placed in a high impedance state. This OEB
function is not intended for rapid access to the data bus. Note
that OEB is referenced to the digital output driver supply
(DRVDD) and should not exceed that supply voltage.
When using the SPI, the data outputs and DCO of each channel
can be independently three-stated by using the output enable
bar bit (Bit 4) in Register 0x14.
Table 13. Output Data Format
Input (V)
VIN+ − VIN−
VIN+ − VIN−
VIN+ − VIN−
VIN+ − VIN−
VIN+ − VIN−
AN-877
SCLK/DFS
Offset binary (default)
Twos complement
Condition (V)
< −VREF − 0.5 LSB
= −VREF
= 0
= +VREF − 1.0 LSB
> +VREF − 0.5 LSB
Application Note, Interfacing to High
SDIO/DCS
DCS disabled
DCS enabled
(default)
Offset Binary Output Mode
0000 0000 0000 0000
0000 0000 0000 0000
1000 0000 0000 0000
1111 1111 1111 1111
1111 1111 1111 1111
Rev. A | Page 33 of 44
TIMING
The AD9268 provides latched data with a pipeline delay of
12 clock cycles. Data outputs are available one propagation
delay (t
The length of the output data lines and loads placed on them
should be minimized to reduce transients within the AD9268.
These transients can degrade converter dynamic performance.
The lowest typical conversion rate of the AD9268 is 10 MSPS.
At clock rates below 10 MSPS, dynamic performance can degrade.
Data Clock Output (DCO)
The AD9268 provides two data clock output (DCO) signals
intended for capturing the data in an external register. In CMOS
output mode, the data outputs are valid on the rising edge of DCO,
unless the DCO clock polarity has been changed via the SPI. In
LVDS output mode, the DCO and data output switching edges
are closely aligned. Additional delay can be added to the DCO
output using SPI Register 0x17 to increase the data setup time.
In this case, the Channel A output data is valid on the rising
edge of DCO, and the Channel B output data is valid on the
falling edge of DCO. See Figure 2, Figure 3, and Figure 4 for a
graphical timing description of the output modes.
PD
) after the rising edge of the clock signal.
Twos Complement Mode
1000 0000 0000 0000
1000 0000 0000 0000
0000 0000 0000 0000
0111 1111 1111 1111
0111 1111 1111 1111
AD9268
1
0
1
OR
0
0

Related parts for AD9268BCPZ-105