AD9516-3BCPZ-REEL7 Analog Devices Inc, AD9516-3BCPZ-REEL7 Datasheet - Page 29
![IC,Ten Distributed-Output Clock Driver,LLCC,64PIN,PLASTIC](/photos/6/50/65021/505-64-lfcsp_sml.jpg)
AD9516-3BCPZ-REEL7
Manufacturer Part Number
AD9516-3BCPZ-REEL7
Description
IC,Ten Distributed-Output Clock Driver,LLCC,64PIN,PLASTIC
Manufacturer
Analog Devices Inc
Type
Clock Generator, Fanout Distributionr
Datasheet
1.AD9516-3BCPZ.pdf
(80 pages)
Specifications of AD9516-3BCPZ-REEL7
Pll
Yes
Input
Clock
Output
CMOS, LVDS, LVPECL
Number Of Circuits
1
Ratio - Input:output
1:14
Differential - Input:output
Yes/Yes
Frequency - Max
2.25GHz
Divider/multiplier
Yes/No
Voltage - Supply
3.135 V ~ 3.465 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LFCSP
Frequency-max
2.25GHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AD9516-3/PCBZ - BOARD EVAL FOR AD9516-3 2.0GHZ
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Internal VCO and Clock Distribution
When using the internal VCO and PLL, the VCO divider must
be employed to ensure that the frequency presented to the
channel dividers does not exceed their specified maximum
frequency of 1600 MHz (see Table 3). The internal PLL uses an
external loop filter to set the loop bandwidth. The external loop
filter is also crucial to the loop stability.
When using the internal VCO, it is necessary to calibrate the
VCO (Register 0x018[0]) to ensure optimal performance.
For internal VCO and clock distribution applications, use the
register settings that are shown in Table 24.
REFIN (REF1)
REFIN (REF2)
BYPASS
RESET
SYNC
SCLK
SDIO
SDO
CLK
CLK
PD
CS
LF
REF1
REF2
REGULATOR (LDO)
LOW DROPOUT
VCO
AD9516-3
CONTROL
DIGITAL
SWITCHOVER
SERIAL
STATUS
LOGIC
REFERENCE
PORT
REF_SEL
STATUS
VS
PRESCALER
2, 3, 4, 5, OR 6
1
P, P + 1
DIVIDE BY
GND
0
VCO STATUS
N DIVIDER
DIVIDER
Figure 44. Internal VCO and Clock Distribution
R
COUNTERS
DISTRIBUTION
DIVIDE BY
DIVIDE BY
REFERENCE
1 TO 32
1 TO 32
A/B
RSET
Rev. A | Page 29 of 80
DIVIDE BY
DIVIDE BY
DIVIDE BY
1 TO 32
1 TO 32
1 TO 32
PROGRAMMABLE
PROGRAMMABLE
R DELAY
N DELAY
REFMON
Table 24. Settings When Using Internal VCO
Register
0x010[1:0] = 00b
0x010 to 0x01E
0x018[0] = 0b,
0x232[0] = 1b
0x1E0[2:0]
0x1E1[0] = 0b
0x1E1[1] = 1b
0x018[0] = 1b,
0x232[0] = 1b
DIVIDE BY
DIVIDE BY
1 TO 32
1 TO 32
FREQUENCY
DETECTOR
DETECT
PHASE
LOCK
Function
PLL normal operation (PLL on).
PLL settings. Select and enable a reference
input; set R, N (P, A, B), PFD polarity, and I
according to the intended loop configuration.
Reset VCO calibration. This is not required
the first time after power-up, but it must
be performed subsequently.
Set VCO divider to divide-by-2, divide-by-3,
divide-by-4, divide-by-5, and divide-by-6.
Use the VCO divider as source for the
distribution section.
Select VCO as the source.
Initiate VCO calibration.
CPRSET VCP
∆
∆
∆
∆
t
t
t
t
CHARGE
PUMP
LVDS/CMOS
LVDS/CMOS
HOLD
LVPECL
LVPECL
LVPECL
OUT0
OUT0
OUT1
OUT1
OUT2
OUT2
OUT3
OUT3
OUT4
OUT4
OUT5
OUT5
OUT6 (OUT6A)
OUT6 (OUT6B)
OUT7 (OUT7A)
OUT7 (OUT7B)
OUT8 (OUT8A)
OUT8 (OUT8B)
OUT9 (OUT9A)
OUT9 (OUT9B)
LD
CP
STATUS
AD9516-3
CP
,