AD9522-5BCPZ Analog Devices Inc, AD9522-5BCPZ Datasheet - Page 13

• Manufacturer Part Number: AD9522-5BCPZ
• Description: 12- Channel Clock Generator With Integra
• Manufacturer: Analog Devices Inc
• Type: Clock Generator, Fanout Distributionr

Specifications of AD9522-5BCPZ

• Pll: Yes
• Input: CMOS, LVDS, LVPECL
• Output: CMOS, LVDS
• Number Of Circuits: 1
• Ratio - Input:output: 2:12, 2:24
• Differential - Input:output: Yes/Yes
• Frequency - Max: 2.4GHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 3.135 V ~ 3.465 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 64-LFCSP
• Frequency-max: 800MHz
• Ic Interface Type: I2C, SPI
• Frequency: 2.4GHz
• No. Of Outputs: 12
• No. Of Multipliers / Dividers: 4
• Supply Voltage Range: 3.135V To 3.465V
• Digital Ic Case Style: LFCSP
• No. Of Pins: 64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PD, SYNC, AND RESET PINS
Table 12.
Parameter
INPUT CHARACTERISTICS
RESET TIMING
SYNC TIMING
SERIAL PORT SETUP PINS: SP1, SP0
Table 13.
Parameter
SP1, SP0
LD, STATUS, AND REFMON PINS
Table 14.
Parameter
OUTPUT CHARACTERISTICS
MAXIMUM TOGGLE RATE
ANALOG LOCK DETECT
REF1, REF2, AND CLK FREQUENCY STATUS MONITOR
LD PIN COMPARATOR
Logic Level ½
Output Voltage High, V
Output Voltage Low, V
Capacitance
Normal Range
Extended Range
Trip Point
Hysteresis
Logic 1 Voltage
Logic 0 Voltage
Logic 1 Current
Logic 0 Current
Capacitance
Pulse Width Low
RESET Inactive to Start of Register Programming
Pulse Width Low
Logic Level 0
Logic Level 1
Min
0.4 × VS
0.8 × VS
OL
OH
Typ
Max
0.25 × VS
0.65 × VS
Unit
V
V
V
Min
2.7
1.02
8
Min
2.0
50
100
1.3
Typ
100
3
1.6
260
Typ
−110
2
Test Conditions/Comments
These pins do not have internal pull-up/pull-down resistors
VS is the voltage on the VS pin
User can float these pins to obtain Logic Level ½; if floating these pins, user
should connect a capacitor to ground
Rev. 0 | Page 13 of 76
Max
0.4
Max
0.8
1
Unit
V
V
MHz
pF
MHz
kHz
V
mV
Unit
V
V
μA
μA
pF
ns
ns
ns
Test Conditions/Comments
When selected as a digital output (CMOS); there are other
modes in which these pins are not CMOS digital outputs;
see Table 47, 0x017, 0x01A, and 0x01B
Applies when mux is set to any divider or counter output,
or PFD up/down pulse; also applies in analog lock detect
mode; usually debug mode only; note that spurs can
couple to output when any of these pins are toggling
On-chip capacitance; used to calculate RC time constant
for analog lock detect readback; use a pull-up resistor
Frequency above which the monitor indicates the
presence of the reference
Frequency above which the monitor indicates the
presence of the reference
Test Conditions/Comments
Each of these pins has an internal 30 kΩ pull-up resistor
The minus sign indicates that current is flowing out of
the AD9522, which is due to the internal pull-up resistor
High speed clock is CLK input signal
AD9522-5