ADSP-2189MBSTZ-266 Analog Devices Inc, ADSP-2189MBSTZ-266 Datasheet - Page 3

• Manufacturer Part Number: ADSP-2189MBSTZ-266
• Description: IC,DSP,16-BIT,CMOS,QFP,100PIN,PLASTIC
• Manufacturer: Analog Devices Inc
• Series: ADSP-21xxr
• Type: Fixed Pointr

Specifications of ADSP-2189MBSTZ-266

• Interface: Host Interface, Serial Port
• Clock Rate: 66MHz
• Non-volatile Memory: External
• On-chip Ram: 192kB
• Voltage - I/o: 3.30V
• Voltage - Core: 2.50V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 100-LQFP
• Device Core Size: 16b
• Format: Fixed Point
• Clock Freq (max): 66MHz
• Mips: 66
• Device Input Clock Speed: 66MHz
• Ram Size: 192KB
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (min): 2.25V
• Operating Supply Voltage (max): 2.75/3.6V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ADSP-2189MBSTZ266

The internal result (R) bus connects the computational units so
that the output of any unit may be the input of any unit on the
next cycle.
A powerful program sequencer and two dedicated data address
generators ensure efficient delivery of operands to these compu-
tational units. The sequencer supports conditional jumps, sub-
routine calls and returns in a single cycle. With internal loop
counters and loop stacks, the ADSP-2189M executes looped
code with zero overhead; no explicit jump instructions are re-
quired to maintain loops.
Two data address generators (DAGs) provide addresses for
simultaneous dual operand fetches (from data memory and
program memory). Each DAG maintains and updates four
address pointers. Whenever the pointer is used to access data
(indirect addressing), it is post-modified by the value of one of
four possible modify registers. A length value may be associated
with each pointer to implement automatic modulo addressing
for circular buffers.
Efficient data transfer is achieved with the use of five internal
buses:
• Program Memory Address (PMA) Bus
• Program Memory Data (PMD) Bus
• Data Memory Address (DMA) Bus
• Data Memory Data (DMD) Bus
• Result (R) Bus
The two address buses (PMA and DMA) share a single external
address bus, allowing memory to be expanded off-chip and the
two data buses (PMD and DMD) share a single external data
bus. Byte memory space and I/O memory space also share the
external buses.
Program memory can store both instructions and data, permit-
ting the ADSP-2189M to fetch two operands in a single cycle,
one from program memory and one from data memory. The
ADSP-2189M can fetch an operand from program memory and
the next instruction in the same cycle.
In lieu of the address and data bus for external memory connec-
tion, the ADSP-2189M may be configured for 16-bit Internal
DMA port (IDMA port) connection to external systems. The
IDMA port is made up of 16 data/address pins and five control
pins. The IDMA port provides transparent, direct access to the
DSPs on-chip program and data RAM.
An interface to low cost byte-wide memory is provided by the
Byte DMA port (BDMA port). The BDMA port is bidirectional
and can directly address up to four megabytes of external RAM
or ROM for off-chip storage of program overlays or data tables.
The byte memory and I/O memory space interface supports
slow memories and I/O memory-mapped peripherals with pro-
grammable wait-state generation. External devices can gain
control of external buses with bus request/grant signals (BR,
BGH and BG). One execution mode (Go Mode) allows the
ADSP-2189M to continue running from on-chip memory.
Normal execution mode requires the processor to halt while
buses are granted.
The ADSP-2189M can respond to eleven interrupts. There can
be up to six external interrupts (one edge-sensitive, two level-
sensitive and three configurable) and seven internal interrupts
generated by the timer, the serial ports (SPORTs), the Byte
DMA port and the power-down circuitry. There is also a master
REV. A
–3–
RESET signal. The two serial ports provide a complete synchro-
nous serial interface with optional companding in hardware and
a wide variety of framed or frameless data transmit and receive
modes of operation.
Each port can generate an internal programmable serial clock or
accept an external serial clock.
The ADSP-2189M provides up to 13 general-purpose flag pins.
The data input and output pins on SPORT1 can be alternatively
configured as an input flag and an output flag. In addition, eight
flags are programmable as inputs or outputs and three flags are
always outputs.
A programmable interval timer generates periodic interrupts. A
16-bit count register (TCOUNT) decrements every n processor
cycles, where n is a scaling value stored in an 8-bit register
(TSCALE). When the value of the count register reaches zero,
an interrupt is generated and the count register is reloaded from
a 16-bit period register (TPERIOD).
Serial Ports
The ADSP-2189M incorporates two complete synchronous
serial ports (SPORT0 and SPORT1) for serial communications
and multiprocessor communication.
Here is a brief list of the capabilities of the ADSP-2189M
SPORTs. For additional information on Serial Ports, refer to
the ADSP-2100 Family User’s Manual, Third Edition.
• SPORTs are bidirectional and have a separate, double-buff-
• SPORTs can use an external serial clock or generate their
• SPORTs have independent framing for the receive and trans-
• SPORTs support serial data word lengths from 3 to 16 bits
• SPORT receive and transmit sections can generate unique
• SPORTs can receive and transmit an entire circular buffer of
• SPORT0 has a multichannel interface to selectively receive
• SPORT1 can be configured to have two external interrupts
PIN DESCRIPTIONS
The ADSP-2189M will be available in a 100-lead LQFP pack-
age. In order to maintain maximum functionality and reduce
package size and pin count, some serial port, programmable
flag, interrupt and external bus pins have dual, multiplexed
functionality. The external bus pins are configured during
RESET only, while serial port pins are software configurable
during program execution. Flag and interrupt functionality is
retained concurrently on multiplexed pins. In cases where pin
ered transmit and receive section.
own serial clock internally.
mit sections. Sections run in a frameless mode or with frame
synchronization signals internally or externally generated.
Frame sync signals are active high or inverted, with either of
two pulsewidths and timings.
and provide optional A-law and µ-law companding according
to CCITT recommendation G.711.
interrupts on completing a data word transfer.
data with only one overhead cycle per data word. An interrupt
is generated after a data buffer transfer.
and transmit a 24- or 32-word, time-division multiplexed,
serial bitstream.
(IRQ0 and IRQ1) and the Flag In and Flag Out signals. The
internally generated serial clock may still be used in this con-
figuration.
ADSP-2189M