ADUM6132ARWZ-RL Analog Devices Inc, ADUM6132ARWZ-RL Datasheet
ADUM6132ARWZ-RL
Specifications of ADUM6132ARWZ-RL
Related parts for ADUM6132ARWZ-RL
ADUM6132ARWZ-RL Summary of contents
Page 1
FEATURES isoPower integrated isolated high-side supply 275 mW isolated dc-to-dc converter 200 mA output sink current, 200 mA output source current High common-mode transient immunity: >50 kV/μs Wide-body 16-lead SOIC package Safety and regulatory approvals (pending) UL recognition 3750 V ...
Page 2
ADuM6132 TABLE OF CONTENTS Features .............................................................................................. 1 Applications ....................................................................................... 1 General Description ......................................................................... 1 Functional Block Diagram .............................................................. 1 Revision History ............................................................................... 2 Specifications ..................................................................................... 3 Electrical Characteristics ............................................................. 3 Package Characteristics ............................................................... 4 Regulatory Information ............................................................... 4 Insulation and ...
Page 3
SPECIFICATIONS ELECTRICAL CHARACTERISTICS All voltages are relative to their respective ground; 4.5 V ≤ V specifications apply over the entire recommended operating range, unless otherwise noted. All typical specifications are 5 ...
Page 4
ADuM6132 Parameter 1 Part-to-Part Matching Output Rise Time (10% to 90%) Output Fall Time (10% to 90%) 1 See the Terminology section supplied by the output of the integrated isolated dc-to-dc power supply. I DDA 3 Duration ...
Page 5
DIN V VDE V 0884-10 (VDE V 0884-10) INSULATION CHARACTERISTICS The ADuM6132 is suitable for reinforced electrical isolation only within the safety limit data. Maintenance of the safety data is ensured by protective circuits. The asterisk (*) marking on the ...
Page 6
ADuM6132 ABSOLUTE MAXIMUM RATINGS T = 25°C, unless otherwise noted. A Table 7. Parameter Rating Storage Temperature Range, T −55°C to +150°C ST Ambient Operating Temperature −40°C to +85°C Range Input Supply Voltage −0.5 ...
Page 7
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS Table 8. Pin Function Descriptions Pin No. Mnemonic Description 1 V Input Supply Voltage for Isolated Power Supply GND Ground Reference for Isolated Power Supply Input and ...
Page 8
ADuM6132 TYPICAL PERFORMANCE CHARACTERISTICS All typical performance curves are based on operation at T 16.0 15.5 15.0 14 4. 13.5 13 LOAD CURRENT (mA) ISO Figure 4. Typical V ...
Page 9
V DDA DDA 15V DDA 200 400 600 V DATA FREQUENCY (kHz) OA Figure 10. Typical I Supply Current 200 pF DDA ...
Page 10
ADuM6132 TERMINOLOGY Channel-to-Channel Matching Channel-to-channel matching with rising or falling matching edge polarity is the magnitude of the propagation delay differ- ence between two channels of the same part when the inputs are both rising edges or both falling edges. ...
Page 11
APPLICATIONS INFORMATION TYPICAL APPLICATION USAGE The architecture of the ADuM6132 is ideal for motor drive and inverter applications where the low-side channels are common to the controller. This arrangement requires only two isolation regions in a package. All the isolated ...
Page 12
ADuM6132 In applications involving high common-mode transients, care should be taken to ensure that board capacitive coupling across the isolation barrier is minimized. Furthermore, the board layout should be designed so that any coupling that does occur affects all pins ...
Page 13
PROPAGATION DELAY-RELATED PARAMETERS Propagation delay is a parameter that describes the time it takes a logic signal to propagate through a component. The propaga- tion delay to a logic low output may differ from the propagation delay to a logic ...
Page 14
ADuM6132 Note that in the presence of strong magnetic fields and high frequencies, any loops formed by PCB traces may induce sufficiently large error voltages to trigger the threshold of succeeding circuitry. Care should be taken in the layout of ...
Page 15
... CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. ORDERING GUIDE No. of Output Peak Model Channels Current (A) 1 ADuM6132ARWZ 2 0.2 ADuM6132ARWZ- 0 RoHS Compliant Part. 10.50 (0.4134) 10.10 (0.3976 7.60 (0.2992) 7.40 (0.2913 ...
Page 16
ADuM6132 NOTES ©2008 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D07393-0-7/08(0) Rev Page ...