EVAL-AD5270SDZ Analog Devices Inc, EVAL-AD5270SDZ Datasheet - Page 6

• Manufacturer Part Number: EVAL-AD5270SDZ
• Description: EVALUATION BOARD
• Manufacturer: Analog Devices Inc

Specifications of EVAL-AD5270SDZ

• Main Purpose: Digital Potentiometer
• Embedded: No
• Utilized Ic / Part: AD5270
• Primary Attributes: 1 Channel, 1024 Position
• Secondary Attributes: 2.7 ~ 5.5 V, 5 ppm/°C, SPI Interfaces
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AD5270/AD5271
Parameter
DYNAMIC CHARACTERISTICS
1
2
3
4
5
6
7
8
9
10
11
Table 5. AD5271—20 kΩ Resistor Performance Mode Code Range
Resistor Tolerance per Code
R-TOLERANCE
Table 6. AD5271—50 kΩ and 100 kΩ Resistor Performance Mode Code Range
Resistor Tolerance per Code
R-TOLERANCE
Typical specifications represent average readings at 25°C, V
Resistor position nonlinearity error (R-INL) is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper
positions. R-DNL measures the relative step change from ideal between successive tap positions.
The maximum current in each code is defined by I
The terms resistor performance mode and R-Perf mode are used interchangeably. See the Resistor Performance Mode section.
Guaranteed by design and not subject to production test.
See Figure 25 for more details.
Resistor Terminal A and Resistor Terminal W have no limitations on polarity with respect to each other. Dual-supply operation enables ground referenced bipolar
signal adjustment.
Different from operating current, the supply current for the fuse program lasts approximately 55 ms.
Different from operating current, the supply current for the fuse read lasts approximately 500 ns.
P
All dynamic characteristics use V
Bandwidth
Total Harmonic Distortion
Resistor Noise Density
1% R-Tolerance
2% R-Tolerance
3% R-Tolerance
1% R-Tolerance
2% R-Tolerance
3% R-Tolerance
DISS
is calculated from (I
DD
× V
DD
) + (I
5, 11
DD
= +2.5 V, V
SS
× V
SS
).
SS
= −2.5 V.
AW
Symbol
= (V
DD
− 1)/R
DD
|V
From 0x1E to 0xFF
From 0x0F to 0xFF
From 0x06 to 0xFF
R
From 0x1E to 0xFF
From 0x14 to 0xFF
From 0x0A to 0xFF
AW
= 5 V, and V
DD
= 50 kΩ
AW
− V
Test Conditions/Comments
−3 dB, R
R
R
R
V
R
R
R
Code = half scale, T
R
R
R
.
AW
AW
AW
A
AW
AW
AW
AW
AW
AW
SS
= 1 V rms, f = 1 kHz, code = half scale
| = 4.5 V to 5.5 V
= 20 kΩ
= 50 kΩ
= 100 kΩ
= 20 kΩ
= 50 kΩ
= 100 kΩ
= 20 kΩ
= 50 kΩ
= 100 kΩ
Rev. E | Page 6 of 24
SS
= 0 V.
AW
= 10 kΩ, Terminal W, see Figure 42
A
= 25°C
|V
From 0x0E to 0xFF
R
From 0x0F to 0xFF
From 0x32 to 0xFF
From 0x19 to 0xFF
From 0x14 to 0xFF
From 0x0A to 0xFF
AW
DD
= 100 kΩ
− V
Min
SS
| = 2.7 V to 4.5 V
Typ
300
120
60
−90
−88
−85
50
25
32
1
Max
Unit
kHz
dB
nV/√Hz