E53-COV07 Omron, E53-COV07 Datasheet
E53-COV07
Specifications of E53-COV07
Related parts for E53-COV07
E53-COV07 Summary of contents
Page 1
... Order control output boards and option boards separately. A single output board and option board can be mounted to each base unit. For example, for a relay control output, order the E53-R4R4 output board in addition to the E5CK-TAA1-500 Process Controller. Model with -500 has a terminal cover for finger protection J Process Controllers Stock Note: Shaded models are normally stocked ...
Page 2
... LEDs Manual output, heating/cooling control, SP limiter, loop burnout alarm, MV limiter, MV change rate limiter, input digital filter, input shift, run/reset, protect functions, scaling function Ramp/Soak Process Controller Max. quantity Model 1 E54-CT1 1 E54-CT3 1 E53-COV07 1 Thermo Tools (see Note) E5CK- -T A--181 ...
Page 3
J Characteristics Thermocouple Indication accuracy y (S (See Note Platinum resistance thermometer Analog input Hysteresis Proportional band (P) Integral (reset) time (I) Derivative (rate) time (D) Control period Manual reset value Alarm setting range Set time ...
Page 4
... Description E53-CKB Event input Communications E53-CK01 RS-232C E53-CK03 RS-485 E53-CKF Transfer output Note: Event input is used for switching the pattern number, run or reset command, or automatic and manual mode with an external signal input. Temperature Ranges Platinum Resistance Thermometer Input (switch selectable) Range Resolution ° ...
Page 5
... Operation Indicators RUN/RST Key Dimensions Unit: mm (inch) J E5CK-T 58 (2.28) 53L x 53W J Accessories Terminal Cover E53-COV07 44.3 (1.74) 44.3 (1.74) Note: Terminal cover is supplied for controller with -500 in the part number; for non-500 model, order separately. A--184 Ramp/Soak Process Controller Display 1 Display 2 ...
Page 6
Installation J Main Parts Terminals Output Board Housing Input type connector Option Board J Removing Internal Mechanism While pressing the hooks on the left and right sides of the front panel, carefully pull the internal mechanism from the housing. (Refer ...
Page 7
... TC S PT: Temperature input After setting the jumper, put on the housing, pressing the housing until the hooks of the front panel snap on. Terminal Cover The E5CK-AA1-500 Controller is provided with a terminal cover E53-COV07. Fasten the terminal cover as follows by using the snap pin. A--186 Ramp/Soak Process Controller ...
Page 8
J Wiring Terminals Terminal Arrangement E5CK-T OUT1 AC100--240V 50/60 Hz (AC/DC24V SOURCE 4 3 SUB1 EV1 RS232C RS485 TRSF 10 OUT2 TRSF: Transfer output EV1:Event input Ramp/Soak Process ...
Page 9
... Power Blocks for E5CK- -T The E5CK-T has independent power supplies for each of the terminal blocks shown below. Note: The power supplies for blocks C (exclude relay output) and D are shared for the following option board: E53-CKB or E53-CKF Option Board E5CK ...
Page 10
... Terminal numbers 9 and 10 are for control output 2 (OUT2). The three output types and internal equalizing circuits are available according to the output board GND 9 Relay NPN E53-R4R4 /E53-V44R4 E53-Q4Q4 E53-Q4R4 /E53-C4R4 E53-Q4HR4/E53-C4DR4 Specifications for Each Type of Output Output type Specifications Relay 250 VAC ...
Page 11
Precautions J Operating Environment • Operate the Controller within the rated ambient operating temperature, ambient operating humidity, and storage tem- perature ranges. • Use the Controller according to the vibration resistance, shock resistance, and enclosure ratings. • Do not install ...
Page 12
J SSR Connection Example of Process Controller and SSR Digital Controller + Voltage output terminal (for driving SSR) -- Connectable E5jK-T Process Controller with Voltage Output (12 VDC max.) E5CK-T Controller with Voltage Output (12 VDC ...
Page 13
...
Page 14
Cat. No. H301-E3-1 6/04 Specifications subject to change without notice Printed in USA ...