M2PJ-5722-24E Omron, M2PJ-5722-24E Datasheet - Page 220
M2PJ-5722-24E
Manufacturer Part Number
M2PJ-5722-24E
Description
LIGHTED PUSH BUTTON
Manufacturer
Omron
Series
M2Pr
Datasheet
1.M2DA-7001.pdf
(265 pages)
Specifications of M2PJ-5722-24E
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
M2PJ572224ENC
- Current page: 220 of 265
- Download datasheet (11Mb)
A3A
Installation
Mounting and Replacing the Pushbutton
Mounting Direction for the Pushbutton and Switch
•
•
Removing the Pushbutton (Non-lighted Models Only)
•
•
Mounting Switch on a Panel
Mount Leaf Spring
Press the leaf spring into the fitted groove on the upper surface of
the Switch. For an easier fitting, first fit one side of the leaf spring,
then press the other side into the fitting groove.
218
Insert the catches of the Pushbutton into the grooves of the
Switch and push down on the Pushbutton until it is fixed securely
to the Switch.
With lighted models, the LED is built into the Switch and cannot
be replaced.
To remove the Pushbutton, hold both the Pushbutton and the
Switch on the longer sides and pull the Pushbutton away from
the Switch. (If the catches on the Pushbutton are bent outwards,
it may result in malfunction.)
When replacing the Pushbutton, if the cap is held on the sides
with catches, internal components (e.g., plate) may come loose.
Be sure to hold the Pushbutton by the sides without catches (i.e.,
the longer sides of the Switch) when removing.
LED terminals
Grooves in the Switch
Catch
Catches on the Pushbutton
Leaf spring
fitting groove
Switch
Leaf spring
Note: Be sure to fit the leaf spring exactly into the groove, and do
Mount Flange on Panel
Insert the flange from the front surface of the panel.
The flange has two opposing guides to facilitate its insertion into the
panel cutout hole. Be sure the flange does not remain tilted with re-
spect to the panel surface after being installed.
Note: The mounting direction of the flange determines the
Fit Flange with Switch
While holding the flange, insert the opposing supports into the gaps
between the leaf spring and Switch on the longer sides of the hous-
ing, and fit the rectangular hole of the flange with the projections of
the switch housing.
Note: Completely remove any burrs on the panel cutout surface;
Removing Switch
Insert a small flat-bladed screwdriver or tweezers into the flange
support exposed on the rear of the panel. Pry up on each side to pull
out the Switch.
Note: Do not pry up the flange support more than necessary or
Cross Section
not allow it to slip out of the groove.
orientation of the Switch.
otherwise, the flange and Switch will not attach solidly.
the switch holding portions may be damaged.
Panel
Panel
Panel (t = 1 to 1.6 mm)
Flange
Flat-bladed screwdriver
or tweezers
Flange
Guide
Projection
Support
Panel
A3A
Related parts for M2PJ-5722-24E
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
LIGHTED PUSHBUTTON SW
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
L.P.B. INDICATOR
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
L.P.B. INDICATOR
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
PUSHBUTTON
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
INDICATOR LIGHTED PUSH BUTTON
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
LIGHTED PUSHBUTTON
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
LIGHTED PUSH BUTTON SW
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
LIGHTED PUSHBUTTON SW
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
LIGHTED PUSHBUTTON
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: