LTC6905IS5 Linear Technology, LTC6905IS5 Datasheet
LTC6905IS5
Specifications of LTC6905IS5
Available stocks
Related parts for LTC6905IS5
LTC6905IS5 Summary of contents
Page 1
... High Speed Data Bus Clock n Fixed Crystal Oscillator Replacement n Ceramic Oscillator Replacement L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 6614313, 6342817. TYPICAL APPLICATION Basic Connection 17.225MHz ≤ ...
Page 2
... Storage Temperature Range ...................– 65°C to 150°C Lead Temperature (Soldering, 10 sec) .................. 300°C ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL (MINI) TAPE AND REEL LTC6905CS5#TRMPBF LTC6905CS5#TRPBF LTC6905IS5#TRMPBF LTC6905IS5#TRPBF LTC6905HS5#TRMPBF LTC6905HS5#TRPBF LTC6905MPS5#TRMPBF LTC6905MPS5#TRPBF LEAD BASED FINISH TAPE AND REEL (MINI) TAPE AND REEL LTC6905MPS5#TRM LTC6905MPS5#TR TRM = 500 pieces. *The temperature grade is identifi ...
Page 3
... LTC6905HS5 (25°C ≤ T ≤ 125°C), LTC6905IS5 (25°C ≤ T ≤ 85° 2.7V, 17.225MHz < f < 170MHz V+ = 5V, 17.225MHz < f < 170MHz LTC6905MPS5 (–55°C < T < 125°C), LTC6905HS5 (–40°C ≤ T ≤ 125°C), LTC6905IS5 (–40°C ≤ T ≤ 85° 2.7V, 17.225MHz < f < 170MHz + V = 5V, 17.225MHz < ...
Page 4
LTC6905 ELECTRICAL CHARACTERISTICS temperature range, otherwise specifi cations are at T otherwise noted. All voltages are with respect to GND. SYMBOL PARAMETER V Low Level Output Voltage (Note OUT Rise/Fall Time (Note ...
Page 5
TYPICAL PERFORMANCE CHARACTERISTICS + OUT 2.5 3 3.5 4 4.5 5 SUPPLY VOLTAGE (V) 6905 G04 LTC6905 Output Operating at 17.5MHz 1V/DIV 12.5ns/DIV ...
Page 6
LTC6905 BLOCK DIAGRAM + SET I RES SET 3 – – BIAS + GND ±5% RES + (V – SET + GAIN = 1 MASTER OSCILLATOR – I ...
Page 7
THEORY OF OPERATION As shown in the Block Diagram, the LTC6905’s master oscillator is controlled by the ratio of the voltage between + the V and SET pins and the current entering the SET pin (I ). The voltage on ...
Page 8
... JITTER AND POWER SUPPLY NOISE If the LTC6905 is powered by a supply that has frequency greater than 5pF LOAD contents equal to the output frequency then the oscillators ) and output OSC jitter may increase. In addition, power supply ripple in excess of 20mV at any frequency may increase jitter. ...
Page 9
APPLICATIONS INFORMATION JITTER AND DIVIDE RATIO At a given output frequency, a higher master oscillator frequency and a higher divide ratio will result in lower jitter and higher power supply dissipation. Indeterminate jitter percentage will decrease by a factor of ...
Page 10
LTC6905 APPLICATIONS INFORMATION ALTERNATIVE METHODS OF SETTING THE OUTPUT FREQUENCY OF THE LTC6905 The LTC6905 may be programmed by any method that sources a current into the SET pin (Pin 3). The accuracy of the programming is best with a ...
Page 11
... MOLD FLASH SHALL NOT EXCEED 0.254mm 6. JEDEC PACKAGE REFERENCE IS MO-193 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa- tion that the interconnection of its circuits as described herein will not infringe on existing patent rights. S5 Package ...
Page 12
... FAX: (408) 434-0507 ● COMMENTS Single Output, High Frequency Operation Single Output Lower Power 2 4-Phase Outputs 3-Wire or I High Accuracy, No External Resistor Ultralow Power, Resistor Sets Frequency www.linear.com ● ™ Programmable 6905fd LT 0808 REV D • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 2005 ...