G5A01216C THERMODISC, G5A01216C Datasheet
G5A01216C
Specifications of G5A01216C
Related parts for G5A01216C
G5A01216C Summary of contents
Page 1
TCO Series Standard Styles Reliable Global Ratings One Shot Operation Upper Limit Temperature Protection MICROTEMP thermal cutoffs ® from Therm-O-Disc offer an accurate, reliable solution to upper limit protection. Known as a thermal fuse or TCO, the MICROTEMP ® thermal ...
Page 2
... G5A01152C 620599 G4A01167C 481383 G5A01167C 620576 G4A01184C 481386 G5A01184C 620577 G4A01192C 481331 G5A01192C 620578 G4A01216C 481387 G5A01216C 620671 G4A01229C 481388 G5A01229C 620580 G4A01240C 481364 G5A01240C MICROTEMP TCO ® STANDARD DIMENSIONS A Overall Length ± 12 (±3.0) Long Lead B Epoxy Lead Length (Reference) (01) C Case Lead Length ± ...
Page 3
MICROTEMP ® Thermal Cutoffs: INTRODUCTION Upper Limit Temperature Protection MICROTEMP ® thermal cutoffs from Therm-O-Disc offer an accurate, reliable solution to the need for upper limit temperature protection. Known as a thermal fuse, thermal link, or TCO, the ® MICROTEMP ...
Page 4
MICROTEMP G4, G6 & G7 Series TCO Before Operation THERMAL PELLET COMPRESSION SPRING TRIP SPRING CERAMIC BUSHING EPOXY SEAL Grey area shows current path MICROTEMP ® G5 & G8 Series TCO Before Operation THERMAL PELLET COMPRESSION SPRING TRIP SPRING ...
Page 5
MICROTEMP Thermal Cutoffs: TYPES & SPECIFICATIONS MICROTEMP ® thermal cutoffs are available in a range of temperatures and electrical ratings to meet application requirements (see figure 3). There are five primary types of thermal cutoffs available. Standard dimensions of ...
Page 6
MICROTEMP ® TCO Operating Temperature Summary Max. Holding Open Temp Temp T T ° °C °C G4 Series f 072 47 100 077 52 125 084 59 125 093 68 140 098 73 140 104 79 150 ...
Page 7
Lead Configurations The MICROTEMP ® TCO can be furnished with virtually any lead configuration specified for an application. Lead curls are available to match most sizes of screws along with varying lead lengths and lead forms. All types of terminations, ...
Page 8
Lead Cutting Minimum Dimensions Inches (millimeters) ` Dimension A Dimension B 0.95 (24.2) 0.22 (5.6) Tape and Reel Packaging Dimensions – Inches (millimeters) ` Item Dim. A Dim. B GXAA0900TTTC 1.66 (42.1) 2.80 (71.1) G7FA0900TTTC 1.66 (42.1) 2.80 (71.1) 0.031(0.8) ...
Page 9
Product Nomenclature ® MICROTEMP TCO (G – Global, Y – Non Agency, R – Regional) Z – Internal construction ® MICROTEMP TCO Packages G – Rating type (G – Global, Y-Non Agency) Z – Internal construction ( ...
Page 10
Farnell, I have the information you asked for. G4A00 has one short lead and one long lead. G4A01 has 2 long leads. We supply the G4A01 to Farnell so that the customer has the choice and can trim the ...
Page 11
MICROTEMP ® Thermal Cutoffs: TECHNICAL DATA MICROTEMP ® thermal cutoffs, available in a variety of standard and custom configurations, pro- vide reliable one-shot, over-temperature protection in a wide range of applications. Performance can be affected by installation method and proper ...
Page 12
Calibration Temperature It is necessary to select a thermal cutoff rating above the maximum temperature experienced during normal operation, including expected short-term temperature overshoots. The temperatures experienced by the thermal cutoff during normal operation will determine the life expectancy for ...
Page 13
TEMPERATURE OR VOLTAGE MEASURING DEVICE THERMOCOUPLE CONNECTNG CONDUIT WIRE Figure 9 illustrates a typical installation of a thermocoupled cutoff. Note that the body of the thermal cutoff is at the same potential as the connecting circuit; therefore, it must be ...
Page 14
The product and application being tested will determine the ...
Page 15
Substitute actual thermal cutoffs in a sufficient number of finished products and re-run the tests to obtain statistical verification of the results. For multiple TCO applications, test functional thermal cutoffs under fault conditions so that the product overheats and each ...
Page 16
Test samples should be x-rayed before and after the soldering operation. The size of the chemical pellet should be measured with an optical comparator or a toolmaker’s microscope to verify that no shrinkage has occurred during the soldering operation (see ...
Page 17
Splices & Terminals Insecure splices and terminations may produce high resistance junctions which can cause self 2 heating ( power is dissipated across these junctions during product operation. Heat from these hot spots can flow down the thermal ...
Page 18
...
Page 19
...
Page 20
x-ref colour against temperature ...
Page 21
Thermal Gradients Ideal TCO placement subjects the entire TCO case, leads, epoxy seal and internal components to a uniform temperature environment. Care should be exercised in the placement of the TCO to minimize thermal gradients across the TCO body. In ...
Page 22
CAUTION . . . The thermal cutoff may fail to open the electrical circuit under certain conditions. Distortion of the case, breaking or cracking the seal, exposing the epoxy seal to cleaning solvents, compression of the leads and current surges ...
Page 23
Agency Recognition MICROTEMP ® thermal cutoffs are recognized by the following major agencies: UL BEAB Underwriters British Laboratories Inc. Electrotechnical (USA) Approvals Board MICROTEMP ® thermal cutoffs are recognized by the major approval agencies throughout the world for AC circuit ...