585SX4Q25F103SP Honeywell, 585SX4Q25F103SP Datasheet - Page 5

• Manufacturer Part Number: 585SX4Q25F103SP
• Description: Potentiometers 10K Ohm 20% 1/20W 6mm
• Manufacturer: Honeywell
• Type: Potentiometerr
• Series: 585r

Specifications of 585SX4Q25F103SP

• Resistance: 10kohm
• Power Rating: 1/20W
• Tolerance (+ Or -): 20%
• Number Of Turns: 1Turn
• Technology: Carbon Film
• Mounting Style: Panel
• Termination Style: Pin
• Operating Temp Range: -55C to 120C
• Failure Rate: Not Required
• Shaft Diameter (mm): 6mm
• Product Diameter (mm): Not Requiredmm
• Product Length (mm): 19.5mm
• Product Height (mm): 11.35mm
• Product Depth (mm): 9.5mm
• Tolerance: 20 %
• Taper: Linear
• Element Type: Carbon
• Shaft Type: Flatted / D
• Shaft Length: 19.05 mm
• Shaft Diameter: 6 mm
• Product: Commercial Potentiometer
• Voltage Rating: 50 Volts
• Angle, Mechanical: 300 °
• Application: For manual controls, telecommunications and audio equipment
• Diameter, Shaft: 0.236 "
• Dimensions: 9.5mmL×9.5mmW×5mmH
• Linearity: ±5 %
• Material, Element: Carbon
• Mounting Type: PCB
• Power, Rating: 0.05 W
• Rotational Life: 10000 Cycles
• Shaft Style: Flatted Shaft
• Termination: PC Pins
• Voltage, Operating: 50 VAC
• Lead Free Status / RoHS Status: Compliant

How to use this catalogue
For each referenced listing, key specification parameters, descriptions and
mounting drawing information are presented. These illustrate our capabilities
while the specifications include allow easy differentiation between similar
products.
There are, of course, many more product options available. Full product
specification may be accessed on our website (www.honeywell.com/sensing).
At the Home page enter the catalogue listing reference in the SEARCH box and
click GO! This will take you directly to the interactive catalogue/specification
search tables for this listing. Alternatively select and click the interactive
catalogue icon on the Home page and then choose a product category against
which to do a specification search.
Also on the website you can access installation instructions, application notes,
Frequently Asked Questions (FAQs), selection guides and additional technical
information.
Mounting dimensions
Mounting dimensions shown in each product section are for reference only.
For exact information, request an engineering drawing from you nearest
Honeywell sales office or visit our website and access it through the interactive
catalogue. Where dual dimensions are shown on mounting drawings, the first
or upper one is millimetres (mm) and the second or lower is inches (in).
Where single dimensions are shown, they are millimetres (mm), unless
otherwise stated.
To order these products
Simply contact your local Honeywell Sales Representative, your Honeywell
Distributor or your local Honeywell office.
If you need a product not listed in this catalogue
One of Honeywell’s strengths is in application-specific packaging of sensing
technology. Honeywell provides many variations of our basic switches and
sensors. For more information, either browse the full interactive catalogue
available on our website, or telephone the following numbers:
USA
UK
France [phone]
More information on Honeywell Sensing & Control products and how to
contact us can be found on our website.
1-800-537-6945/1-815-537-6945
[phone]
Germany
Italy
[phone]
[phone]/456
www.honeywell.com/sensing
Select the right product – select the right supplier
Delivering excellence in system critical sensing
solutions
A system is critical if the quality, reliability, delivery and customer service
associated with a component part is essential to the performance of the
operation or end product. If a sensor or a switch is critical to the
performance, cost effectiveness, delivery or safety of a product or operation
then it’s systems critical. It is therefore a defining element in the performance
of the system under whatever conditions apply. Failure of the component - or
failure of delivery of the component - results in lost productivity, increased
costs or a catastrophic event such as a shutdown. Therefore selecting the
right product is essential. It can make the difference between success and
failure.
Honeywell Sensing and Control – delivering
excellence
To select the right product, first select the right supplier. To deliver the right
products for our customers’ applications we listen to them to understand their
needs. Using techniques such as “Voice of the Customer and “Concept
Engineering” we make sure that the products and solutions we deliver are the
right ones. As part of Honeywell we can use local knowledge and
understanding combined with global expertise and resources to achieve this.
We can deploy many key technologies to bring innovative solutions to
customers’ problems.
Our products are manufactured to work well and to last. We use Six Sigma
Plus productivity to ensure this is the case. We have award winning
manufacturing facilities around the world and recognised world class
business excellence in manufacturing and supply chain management to
deliver on time, anywhere in the world.
Our e-business approach offers instant access to product information,
technical support and application knowledge through out Internet site. Check
out our powerful new interactive catalogue that can search and find the right
products for customers’ needs and deliver a drawing ready for incorporation
in a CAD system direct to your desk.
And of course, we manage our whole business for the benefit of our
customers, using an acknowledged world-class business excellence approach
that incorporates Six Sigma principles.
Expanded Product Lines
As well as many new and innovative switches, this catalogue includes an
expanded range of Pressure and Position Sensors, previously known under
the Clarostat, NEI and Electrocorporation brand names.
INTRODUCTION
3