FLUKE-700LTP-1 Fluke, FLUKE-700LTP-1 Datasheet
FLUKE-700LTP-1
Manufacturer Part Number
FLUKE-700LTP-1
Description
Low-Pressure Test Pump
Manufacturer
Fluke
Datasheet
1.FLUKE-700LTP-1.pdf
(2 pages)
Specifications of FLUKE-700LTP-1
Operating Pressure Max
100psi
Size
5.9 X 4 X 1.25"
Lead Free Status / RoHS Status
na
Lead Free Status / RoHS Status
na
Introduction
The Fluke-700LTP-1 Low-Pressure Test Pump is a
portable, dual source of vacuum and pressure. Each pump
incorporates a vacuum and pressure selector and fine
adjustment control. The pump has the following
specifications:
Box Contents
Contacting Fluke
To contact Fluke or for service, call one of the following
telephone numbers:
USA: 1-888-44-FLUKE (1-888-443-5853)
Canada: 1-800-36-FLUKE (1-800-363-5853)
Europe: +31 402-675-200
Japan: +81-3-3434-0181
Singapore: +65-738-5655
Anywhere in the world: +1-425-446-5500
Or, visit Fluke's Web site at www.fluke.com.
PN 2811813 April 2007
Output pressure: 0 to 100 psi / 0 to 6.9 bar
Output vacuum: 0 to -13 psi / 0 to -900 mbar
Exposed Materials: Aluminum, silicon, neoprene,
stainless steel, Buna-N
Adjustment: Fine volumetric pressure and vacuum
adjuster
Dimensions: 150 mm x 100 mm
Weight: 226 grams or .5 lbs (pump only)
Fluke 700LTP-1 Low-pressure Test Pump
1/8 in NPT male/female tee
(2) 1 m hoses
(4) 1/8 in NPT male quick connects
(2) 1/8 NPT female to 1/4 in BSP female
Seal Kit
Instruction Sheet
© 2007 Fluke Corporation. All rights reserved. Printed in U.S.A.
A
B
C
D
E
F
G
H
Guidelines for Use
1.
2.
3.
4.
5.
2
Connect a pressure calibrator or pressure module to
the quick-fit connector (item D) at the end of one of the
flexible hoses (item E).
Connect the unit under test to the quick-fit connector
(item D) at the end of the second flexible hose (item
E), choosing correct adapters (item F) and seals.
Turn the fine adjustment control to mid-range.
Set control valve to pressure.
Operate handle (item G) until the pressure is close to
the required value.
Pressure/vacuum release valve- Turn valve counter-
clockwise for vacuum, clockwise for pressure and
centered for release.
Fine adjustment control- Turn in or out to increase or
decrease pressure accordingly.
Master and test port tee
Quick-fit connectors
Hose
1/8 in NPT female to 1/4 in BSP female fitting
Pump Handle. If the pump has not been used for a
while, there may be some resistance on the first
stroke.
Cleanout ports (2)- See cleanout instructions
Low-Pressure Test Pump
7
1
8
Fluke-700LTP-1
Figure 1. Features
Instruction Sheet
4
3
5
eus01f.eps
6
®
1
Related parts for FLUKE-700LTP-1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT PROBE LIGHT
Manufacturer:
Fluke Electronics
Datasheet:
Part Number:
Description:
Watertight Hard Storage Case With Rollers
Manufacturer:
Fluke
Datasheet:
Part Number:
Description:
Dry-Well, Handheld Hi-Temp, Block A
Manufacturer:
HART SCIENTIFIC FLUKE
Part Number:
Description:
(PM5415 / PM5418) Color TV Pattern Generator
Manufacturer:
Fluke
Datasheet:
FLUKE-700LTP-1 Summary of contents
Page 1
... Introduction The Fluke-700LTP-1 Low-Pressure Test Pump is a portable, dual source of vacuum and pressure. Each pump incorporates a vacuum and pressure selector and fine adjustment control. The pump has the following specifications: Output pressure 100 psi / 0 to 6.9 bar Output vacuum -13 psi / 0 to -900 mbar ...
Page 2
... Fluke-700LTP-1 Instruction Sheet Notes The pressure may settle for up to one minute after increasing pressure due to the thermodynamic effects, settling of seals and expansion of the flexible hose. On very high resolutions such as 1 mbar or 0.1 inches of water, small movements of the tubing may result in noticeable pressure changes. ...