STA369BWS STMicroelectronics, STA369BWS Datasheet - Page 44
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
STA369BWS
Manufacturer Part Number
STA369BWS
Description
Multimedia Misc 2.1-channel 40-watt High-EFF Dig Audio
Manufacturer
STMicroelectronics
Datasheet
1.S29AL032D70TFI000.pdf
(67 pages)
Specifications of STA369BWS
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STA369BWS
Manufacturer:
st
Quantity:
20 000
Part Number:
STA369BWS
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
STA369BWSTR
Manufacturer:
NXP
Quantity:
14 300
Part Number:
STA369BWSTR
Manufacturer:
ST
Quantity:
20 000
12.3
12.4
12.5
42
DQ6: Toggle Bit I
DQ2: Toggle Bit II
Reading Toggle Bits DQ6/DQ2
Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete,
or whether the device has entered the Erase Suspend mode. Toggle Bit I may be read at any address, and is
valid after the rising edge of the final WE# pulse in the command sequence (prior to the program or erase
operation), and during the sector erase time-out.
During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause
DQ6 to toggle. (The system may use either OE# or CE# to control the read cycles.) When the operation is
complete, DQ6 stops toggling.
After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6 toggles for
approximately 100 µs, then returns to reading array data. If not all selected sectors are protected, the
Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are
protected.
The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erase-
suspended. When the device is actively erasing (that is, the Embedded Erase algorithm is in progress), DQ6
toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system must
also use DQ2 to determine which sectors are erasing or erase-suspended. Alternatively, the system can use
DQ7 (see the subsection on
If a program address falls within a protected sector, DQ6 toggles for approximately 1 µs after the program
command sequence is written, then returns to reading array data.
DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program
algorithm is complete.
Table 12.1 on page 44
bit algorithm in flowchart form, and the section
algorithm.
differences between DQ2 and DQ6 in graphical form. See also the subsection on
The Toggle Bit II on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that
is, the Embedded Erase algorithm is in progress), or whether that sector is erase-suspended. Toggle Bit II is
valid after the rising edge of the final WE# pulse in the command sequence.
DQ2 toggles when the system reads at addresses within those sectors that have been selected for erasure.
(The system may use either OE# or CE# to control the read cycles.) But DQ2 cannot distinguish whether the
sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is
actively erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected for erasure. Thus,
both status bits are required for sector and mode information. Refer to
outputs for DQ2 and DQ6.
Figure 12.2 on page 43
DQ6/DQ2 on page 42
55
DQ6 in graphical form.
Refer to
toggle bit status, it must read DQ7–DQ0 at least twice in a row to determine whether a toggle bit is toggling.
Typically, the system would note and store the value of the toggle bit after the first read. After the second
read, the system would compare the new value of the toggle bit with the first. If the toggle bit is not toggling,
the device has completed the program or erase operation. The system can read array data on DQ7–DQ0 on
the following read cycle.
However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the
system also should note whether the value of DQ5 is high (see the section on DQ5). If it is, the system should
then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as
DQ5 went high. If the toggle bit is no longer toggling, then the device has successfully completed the program
shows the toggle bit timing diagram.
Figure 12.2 on page 43
Figure 17.9 on page 55
explains the algorithm. See also the
shows the outputs for Toggle Bit I on DQ6.
shows the toggle bit algorithm in flowchart form, and the section
DQ7: Data# Polling on page
for the following discussion. Whenever the system initially begins reading
shows the toggle bit timing diagrams.
S29AL032D
Figure 17.10 on page 55
D a t a
Reading Toggle Bits DQ6/DQ2 on page 42
S h e e t
40).
DQ6: Toggle Bit I
shows the differences between DQ2 and
Figure 12.2 on page 43
Table 12.1 on page 44
Figure 17.10 on page 55
subsection.
S29AL032D_00_A9 January 19, 2007
DQ2: Toggle Bit
Reading Toggle Bits
Figure 17.9 on page
shows the toggle
explains the
to compare
shows the
II.