327913-000 Tyco Electronics, 327913-000 Datasheet - Page 277

• Manufacturer Part Number: 327913-000
• Description: Connector Accessories Hexa Shield Adapter Aluminum Alloy Olive Drab
• Manufacturer: Tyco Electronics
• Type: Hexa Shield Adapterr

Catalog 1654025
Revised 12-04
www.tycoelectronics.com
Dimensions are in millimeters
and inches unless otherwise
specified. Values in brackets
are U.S. equivalents.
Adhesives
Installation Guide
Substrate Preparation
Procedures
Preparation of the substrate
depends on the part to be
bonded. Following are two
preparation procedures.
The first applies to plated
metals and adapters; the
second applies to polymer
molded parts, cable jack-
ets, and tubing materials.
Plated Metals and Adapters
Thoroughly degrease the
surface with a clean cloth
or paper wipe dampened
with a solvent. The cloth or
paper should not be
saturated with the solvent.
Allow the part to stand for
a minute or two to allow
complete evaporation of
the solvent.
Molded Parts, Cable Jackets,
and Tubing Materials
Carefully and evenly abrade
the surface with #320 emery
cloth. Wipe contaminants
and abraded particles away
with a clean cloth or paper
wipe dampened with a sol-
vent. The cloth or paper
should not be saturated
with the solvent. Allow the
part to stand for a minute
or two to allow complete
evaporation of the solvent.
Note:
I
I
I
Avoid contamination of the pre-
pared surface. If using primer,
apply it according to the manufac-
turer’s instructions and allow it to
dry.
Epoxy adhesives may cause skin
and eye irritation. Be sure to
observe the handling instructions.
When using hot-melt adhesives on
substrates with high heat-sink
capacity (such as connector back-
shells), preheat the substrate until
it is hot to touch, then apply the
adhesive tape and shrink the
molded part in place.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Caution:
The use of cleaning solvent
is described in the prepara-
tion of various components
for adhesive bonding.
Please observe the solvent
manufacturer’s safety rec-
ommendations. Several
Raychem epoxy adhesives
and solvent base primers
are also described in some
cases. For specific handling
precautions, please consult
the appropriate Raychem
material safety data sheet
for the adhesive being used.
Installation Procedures
The three sets of installation
instructions that follow are
based on the type and/or
form of adhesive or sealant
to be used.
Select the set of instructions
that applies to your
application.
Tape Adhesives and Sealants
Connector Boot
1. Degrease the area of
2. Lightly abrade the
3. Lightly abrade and wipe
4. When using primer,
5. Double-wrap the
the adapter to which
the boot will be bonded,
using appropriate
solvent on a paper
tissue or clean cloth. Do
not abrade the adapter.
bonding area of the
cable jacket with #320
emery cloth, then wipe
off loose particles with
a tissue or clean cloth
dampened with a
solvent.
25.4 [1.0] back inside
each end of the boot.
apply a thin, uniform
coating to the bonding
surface and let it air dry
(15–20 minutes).
adhesive tape around
the cleaned area of the
adapter, placing slight
tension on the tape as
you wrap. Tack the ends
in place with a soldering
iron or hot tool.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
6. Double-wrap adhesive
7. Position the boot on the
8. Recover the connector
9. Complete the recovery
10. Where oven curing is
Transition
1. Lightly abrade the
2. Abrade and wipe the
3. When using primer,
South America: 55-11-3611-1514
Japan: 81-44-900-5102
Singapore: 65-4866-151
UK: 44-1793-528171
tape around the cable
jacket where the end of
the boot is to be located.
adapter and the cable.
Apply heat, starting at
the connector end.
end of the boot onto the
adapter and continue
heating until the area is
fully recovered and the
adhesive tape is prop-
erly melted.
of the boot, continuing
toward the cable end.
Heat the cable end of
the boot where the
adhesive is placed,
until the part is fully
recovered and the tape
has properly melted or
flowed. The tape should
appear wet, form a bead
or fillet between the
cable and boot, and
show no definition
between the layers
of tape.
required to complete
adhesive bonding, heat
the assembled harness
in a preheated oven
according to the
following schedule:
bonding area of the
cable jacket with #320
emery cloth, then wipe
off loose particles with
a tissue or clean cloth
dampened with a
solvent.
inside of each transition
opening.
apply a thin, uniform
coating to the bonding
surface and let it air dry
(15–20 minutes).
S-1255-02:
2 hours at 155°C [311°F]
S-1124:
90 minutes at 150°C [302°F]
5-5
5