LT4HW-DC24V Panasonic Electric Works, LT4HW-DC24V Datasheet - Page 4
![](/photos/31/30/313027/lt4hwt8-dc24v_l_sml.jpg)
LT4HW-DC24V
Manufacturer Part Number
LT4HW-DC24V
Description
Manufacturer
Panasonic Electric Works
Datasheet
1.LT4HW-DC24V.pdf
(8 pages)
Specifications of LT4HW-DC24V
Lead Free Status / RoHS Status
Compliant
LT4H-W
Setting the operation mode and time range
Setting procedure 1) Setting the time range (Timer T 1 /Timer T 2 )
Setting procedure 2) Setting the operation mode
Set the operation mode with the keys on the front of the LT4H-W timer.
Q Elapsed time display
W Set time display
E T 1 /T 2 operation indicator
R T 1 /T 2 setting value
T Controlled output
Y Lock indicator
U Time units display
1) Setting or changing the operation mode
(1) When the UP or DOWN key at the first digit is pressed with the SET/LOCK
switch pressed, the mode is changed over to the setting mode.
(2) Now release the SET/LOCK switch.
(3) The operation mode in the setting mode is changed over sequentially in the left or right direction by pressing the UP or DOWN key at the first digit, respectively.
(4) The operational mode displayed at present is set by pressing the RESET switch, and the display returns to the normal condition.
2) Setting (changing) the time
(1) Pressing the SET/LOCK key switches the set value display between T1 and T2. Display the timer (T1 or T2) which is to be set (or changed).
(2) After displaying the timer (T1 or T2) which is to be set, press the UP or DOWN key to change the time.
• Checking the operation mode
When the UP or DOWN key at the second digit is pressed with the SET/LOCK switch pressed, the operational mode can be checked.
The display returns to the normal condition after indicating the operational mode for about two seconds. (While the display indicates the operational mode for about two
seconds, the other indicators continue to operate normally.)
• Setting the lock
When the UP or DOWN key at the fourth digit is pressed with the SET/LOCK switch pressed, all keys on the unit are locked.
The timer does not accept any of UP, DOWN and RESET keys.
To release the lock setting, press the UP or DOWN key at the fourth digit again with the set/lock switch pressed.
* Operational mode, adding and subtracting and minimum input signal range cannot be set at T 1 and T 2 , respectively.
• Changing over the T 1 /T 2 setting display
The T1/T2 setting display is changed over by pressing the SET/LOCK switch. (This operation gives no effect on the other operations. The set time and elapsed time
(residual time) at T 1 are linked with those at T 2 .)
• Changing the set time
1) It is possible to change the set time with the UP and DOWN keys even during time delay with the timer. However, be aware of the following points.
2) When the set times at T 1 and T 2 are set to 0, the output becomes ON only while the start input is carried out. However, while the reset input is carried out, the output
becomes OFF.
(1) If the set time is changed to less than the elapsed time with the time delay set to the addition direction, time delay will continue until the elapsed time reaches full
(2) If the time delay is set to the subtraction direction, time delay will continue until “0” regardless of the new set time.
selectable indicator
indicator
scale, returns to zero, and then reaches the new set time. If the set time is changed to a time above the elapsed time, the time delay will continue until the elapsed
time reaches the new set time.
Set the time range with the DIP switches on the side of the LT4H-W timer.
* The 8-pin type does not have the stop input, so that the dip
switch can be changed over between reset and start inputs.
The signal range of the lock input is fixed (minimum 20 ms).
*4
1
2
3
5
6
7
8
Minimum input reset, start, and
Time delay direction
(same for screw terminal type and 8-pin type.)
10
11
stop signal width
3
4
5
6
Pulse input
OFF-start
One operation
Time range
Time range
(Timer T 1 )
(Timer T 2 )
1 2 3
Item
4 5 6 7 8
SET/LOCK
LT4H-W
RESET
T1
T2
OP.
LOCK
Fourth digit
DIP switches
Pulse input
OFF-start
Repeating operation
T1
T2
h
DOWN
UP
m
s
Addition Subtraction
TIMER
20 ms
OFF
Refer to table 1
Refer to table 2
First digit
DIP switch
Pulse input
ON-start
Repeating operation
1 ms
ON
09/2009
1
2
7
8
9
I UP keys
O DOWN keys
P RESET switch
{ SET/LOCK switch
Integrating input
OFF-start
One operation
Changes the corresponding digit of the set time in the addition direc-
tion (upwards)
Changes the corresponding digit of the set time in the subtraction
direction (downwards)
Resets the elapsed time and the output
Changes over the display between T 1 /T 2 settings, sets the operation
mode, checks the operation mode and locks the operation of each key
(such as up, down or reset key).
Ex: Setting operation mode display
(PULSE-A example)
Table 1: Setting the time range (Timer T 1 )
Table 2: Setting the time range (Timer T 2 )
Notes: 1) Set the DIP switches before installing the timer.
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
1
6
DIP switch No.
DIP switch No.
2) When the DIP SW setting is changed, turn off the power once.
3) The DIP switches are set as ON before shipping.
Integrating input
OFF-start
Repeating operation
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
2
7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
3
8
Integrating input
ON-start
Repeating operation
0.01 s to 99.99 s
0.1 s to 999.9 s
1 s to 9999 s
0 min 01 s to 99 min 59 s
0.1 min to 999.9 min
0 h 01 min to 99 h 59 min
0.1 h to 999.9 h
1 h to 9999 h
0.01 s to 99.99 s
0.1 s to 999.9 s
1 s to 9999 s
0 min 01 s to 99 min 59 s
0.1 min to 999.9 min
0 h 01 min to 99 h 59 min
0.1 h to 999.9 h
1 h to 9999 h
Time range
Time range
23