PIC24HJ64GP510A-E/PF Microchip Technology, PIC24HJ64GP510A-E/PF Datasheet - Page 71

• Manufacturer Part Number: PIC24HJ64GP510A-E/PF
• Description: 16 Bit MCU 40MIPS 64KB FLASH 100 TQFP 14x14x1mm TRAY
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ64GP510A-E/PF

• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 64KB (22K x 24)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 32x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 100-TQFP, 100-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

TABLE 6-3:
6.2.1
The oscillator start-up circuitry and its associated delay
timers are not linked to the device Reset delays that
occur at power-up. Some crystal circuits (especially
low-frequency crystals) have a relatively long start-up
time. Therefore, one or more of the following conditions
is possible after the Reset signal is released:
• The oscillator circuit has not begun to oscillate.
• The Oscillator Start-up Timer has not expired (if a
• The PLL has not achieved a lock (if PLL is used).
The device will not begin to execute code until a valid
clock source has been released to the system. There-
fore, the oscillator and PLL start-up delays must be
considered when the Reset delay time must be known.
6.2.2
If the FSCM is enabled, it begins to monitor the system
clock source when the Reset signal is released. If a
valid clock source is not available at this time, the
device automatically switches to the FRC oscillator and
the user can switch to the desired crystal oscillator in
the Trap Service Routine.
 2009 Microchip Technology Inc.
POR
MCLR
WDT
Software
Illegal Opcode
Uninitialized W
Trap Conflict
Note 1:
crystal oscillator is used).
Reset Type
2:
3:
4:
5:
6:
T
T
Power-up Timer delay (if regulator is disabled). T
states, including waking from Sleep mode, only if the regulator is enabled.
T
T
oscillator clock to the system.
T
T
POR AND LONG OSCILLATOR
START-UP TIMES
FAIL-SAFE CLOCK MONITOR
(FSCM) AND DEVICE RESETS
STARTUP
OST
RST
POR
LOCK
FSCM
= Internal state Reset time (20 s nominal).
= Oscillator Start-up Timer. A 10-bit counter counts 1024 oscillator periods before releasing the
= Power-on Reset delay (10 s nominal).
RESET DELAY TIMES FOR VARIOUS DEVICE RESETS
= PLL lock time (20 s nominal).
= Fail-Safe Clock Monitor delay (100 s nominal).
EC, FRC, LPRC
ECPLL, FRCPLL
XT, HS, SOSC
XTPLL, HSPLL
Any Clock
Any Clock
Any clock
Any Clock
Any Clock
Any Clock
Clock Source
= Conditional POR delay of 20 s nominal (if on-chip regulator is enabled) or 64 ms nominal
PIC24HJXXXGPX06A/X08A/X10A
T
T
T
T
POR
POR
POR
POR
SYSRST Delay
+ T
+ T
+ T
+ T
Preliminary
STARTUP
STARTUP
STARTUP
STARTUP
T
T
T
T
T
T
RST
RST
RST
RST
RST
RST
STARTUP
+ T
+ T
+ T
+ T
6.2.2.1
When the system clock source is provided by a crystal
oscillator and/or the PLL, a small delay, T
matically inserted after the POR and PWRT delay
times. The FSCM does not begin to monitor the system
clock source until this delay expires. The FSCM delay
time is nominally 500 s and provides additional time
for the oscillator and/or PLL to stabilize. In most cases,
the FSCM delay prevents an oscillator failure trap at a
device Reset when the PWRT is disabled.
6.3
Most of the Special Function Registers (SFRs) associ-
ated with the CPU and peripherals are reset to a
particular value at a device Reset. The SFRs are
grouped by their peripheral or CPU function and their
Reset values are specified in each section of this
manual.
The Reset value for each SFR does not depend on the
type of Reset, with the exception of two registers. The
Reset value for the Reset Control register, RCON,
depends on the type of device Reset. The Reset value
for the Oscillator Control register, OSCCON, depends
on the type of Reset and the programmed values of the
oscillator Configuration bits in the FOSC Configuration
register.
RST
RST
RST
RST
is also applied to all returns from powered-down
Special Function Register Reset
States
System Clock
T
OST
FSCM Delay for Crystal and PLL
Clock Sources
T
Delay
T
LOCK
OST
+ T
—
—
—
—
—
—
—
LOCK
FSCM
T
T
T
Delay
FSCM
FSCM
FSCM
—
—
—
—
—
—
—
DS70592B-page 71
1, 2, 3
1, 2, 3, 5, 6
1, 2, 3, 4, 6
1, 2, 3, 4, 5, 6
3
3
3
3
3
3
FSCM
Notes
, is auto-